How can I apply the trial load method to my 2D model?

12 December 2014 1 1K Report

I have a 2D model in abaqus and I want to apply the arch effect on my model by a function of pressure on downstream surface. How is the the function of arch effect? linear of another function?

Saeed Farahi Shahri

Your question is not obvious.

you can define an amplitude for arch loading and use of the Load modulus>Mechanical>Pressure

and then specify the amount, direction, amplitude and location of loading.

Good Luck

Badges
Science topic

More Nezisian Soltani's questions See All

Does anyone know about modelling tensile contact behavior in abaqus?

I modeled 2 part in abaqus and i want to until tensile stress between 2 surface is T, it transmit between 2 surface and up to T, to surface be separate of each other. Is there any model in...

04 May 2015 9,447 1 View

How do you request a .fil output in abaqus?

I need a .fil output in abaqus . I typed *node file in input file in abaqus to have a .fil. but when I import input file this warning appears. WARNING: The following keywords/parameters are not...

02 March 2015 3,753 3 View

Is it necessary to use of 3D8R element in damage plasticity model in abaqus?

I want to use of damage plasticity model in abaqus. when i use of 3D8R elements, the running complete easily, but when i use of 3D20R, abaqus cant solve the model. Is it necessary to use of 3D8R...

02 March 2015 6,072 4 View

How can I prevent this problem in converging in explicit analysis in abaqus?

I have a 2D model in abaqus (Explicit) and analysis is quasi-static (with time 50). Material model is damage plasticity. I can see some crack in my model. But when I refine mesh, displacement will...

31 December 2014 6,547 3 View

How to define slide contact between two edge in abaqus explicit in a quasi-static analysis?

I modeled a 2D model in abaqus explicit. My analysis is quasi-static. When I put a hard contact between two edge, a divergence occur in my result. I can understand why this problem occurs. Time in...

31 December 2014 9,935 2 View

I have used of tie constrain in abaqus between two surfaces but after analyzing, two nodes are separate, why?

31 December 2014 7,414 4 View

Error in abaqus: "Stiffnesses of spring element 5 instance is too high..."how can I solve this problem without reducing my stiffness?

I modeled a cantilever in with many springs in downstream of it to model arch effect. but stiffness of my spring is too large and abaqus make an error. how can i solve this problem without reduce...

11 December 2014 3,243 1 View

How can I transfer analysis results to second analysis in Abaqus?

I want to analyze my model in step 1 and by the new load analyze step 2 so that the stress of step 1 is there in step 2.

10 November 2014 5,574 4 View

Can abaquse model the staged construction?

I want to model a Dam in 8 stage.

10 November 2014 9,467 4 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View