How can I plot load vs displacement for two point load in Abaqus?

01 January 1970 1 8K Report

I apply two point load on reinforced concrete continuous beam (each span has one point load) but the load-displacement graph display only for one point load. So How can I plot the total load-displacement graph?

Hassan Bagheri

go through this tutorial videos:

https://www.youtube.com/watch?v=FaK4eRzrLoE

https://www.youtube.com/watch?v=nFOy00Gkxe0&t=17s

https://www.youtube.com/watch?v=hzJxqakfUik&t=29s

Badges
Science topic

More Mekdes Azene's questions See All

How can I solve etabs 2017/2016 'error in reading material' and 'abnormal condition occurred' during run analysis?

I am doing RC frame analysis but run analysis is not doing it appear error dialog box like 'material reading problem' , abnormal condition it needs to terminate' and some times it terminate with...

11 December 2019 5,272 2 View

Can I model reinforced concrete tall building by taking the material property as isometric and homogenous in ansys workbench ?

I want to model RC tall building by ansys workbench and I do not want to go ansys apdl .In ansys workbench if we assume the material as isotropic and homogeneous the result will be depending on...

09 October 2019 4,342 2 View

From which point of view we assume the dimentions of structural elements before doing structural design?

I am going to check the effectiveness of tuned liquid damper as seismic control and i want to take sample multi story building with out designing the structural elements. so to take that sample...

04 May 2019 2,629 7 View

Is it compatable for partial fullfilment of masters os science in structural enineering?

to know finding of the reason to get strain hardening for stress strain curve is enough for masters level.

01 January 1970 10,056 0 View

How can decrease large deformation in Abaqus?

I model reinforced concrete continuous deep beam but I get large deformation. And in the warning box there is a message related with interaction between steel plate and concrete (I use tie...

01 January 1970 9,393 7 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

There is possible way to calculate experimental DOS from the UPS spectrum of the material. How to calculate the DOS from UPS?

Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.

29 July 2024 4,971 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View