25 July 2020 2 9K Report

Hello all!

I am trying to simulate a problem where a drop deforms under the given flowing conditions of ambient fluid. I want to have a coarse grid throughout the domain, but different levels of refinement should be present near the interface. I want the mesh to be refined after every few timesteps. Is there any predefined function in Fluent to implement this or do I need to use a UDF?

More Sai Subhankar Varanasi's questions See All
How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to empty large intestine in mice ?

Hi all I am working on colon-targeted drug delivery for which I kept mice fasting for 6h using fasting grills during scotophase (dark period). I observed liquid fecal content in the cecum and...

23 February 2021 7,701 2 View

What is the main advantage of using observer based fault tolerant controller(FTC) for sensor fault tolerance?

I am working on FTC for handling sensor faults in the system. I have read about observer-based FTC schemes which use error threshold-based logic between the states and estimated states. If a...

10 January 2021 5,771 2 View

Can we measure porosity of a composite by DSC (heat flow measurements)?

In the DSC conducted for A and B (image provided). B is a derivative of A. Can I conclude that the porosity of composite B is more than A, Since the heat flow is decreasing with increase in...

26 December 2020 9,104 3 View

Is there any guidelines/ recommendations to prevent or control screen addiction in children?

Nowadays, we are encountering with screen addiction in children especially during lockdown. I want to know any guidelines for screen control?

24 December 2020 7,194 3 View

Can a luenberger observer (even a modified version) be effective for a nonlinear affine system?

I want to know whether a luenberger observer or a modified form of it be effective for estimating the states of a system of the following forms: 1. x_dot = f(x,u,d); y = x 2. x_dot = f(x,u); y =...

20 December 2020 1,392 4 View

Can I carry out LC-MS for AuNPs?

Will it be helpful to know the nature of stabilizers used in synthesis of curcumin (if it has polymerized or not). Any specific measures to be followed to carry out these kind of experiments?

15 December 2020 2,283 4 View

Question on calculating the static mean polarizabilities using Gaussian Output files?

I performed an opt calculation on molecule A and got A_opt. I performed a freq calculation on A_opt and got A_opt_freq I performed a polar calculation on A_opt and got A_opt_polar. The A_opt_freq...

09 December 2020 1,188 1 View

How do we choose an appropriate isovalue in ESP/MESP analysis?

I am a beginner to this particular side of the theoretical analysis of a molecule using Gaussian and GaussView. What do the isovalues mean? What physical significance do they hold? How does one...

30 November 2020 1,648 3 View

How to represent Input data as multinomial distribution of feature vectors?

Hello everyone, Is there any approach to generate a fixed no. of feature vectors from the sequential data(similar to time series data...) and also express the same sequential data in terms of the...

29 November 2020 5,508 3 View

Similar questions and discussions
What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close