How can I found the temperature variation from the heated pipe with fluid fluowind inside the tube with 12.5 bar pressure and 45 Celsius temperature?

More Rammohan Gupta's questions See All

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Some new emerging problems on application of RL for scheduling in IoT networks?

I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...

01 August 2024 8,754 2 View

How to make soil water characteristic curve using centrifuge?

We have no access of pressure plate apparatus

22 July 2024 3,488 2 View

What is the degassing temperature and time for biochar for BET surface area analysis if TGA is not possible?

Since BET and TGA both are very costly instruments and many places the facilities are not available (for large number of samples) hence a threshold degassing temperature and time is preferable

16 July 2024 8,112 2 View

Can we analyse RMSD for peptide-HLA docking and binding affinity for peptide-HLA to TCR docking, in a peptide-HLA-TCR docking ?

In the peptide-HLA-TCR docking process, can we express the result of peptide-HLA docking in RMSD and for peptide-HLA to TCR docking, can results be expressed in binding affinity?

11 July 2024 4,831 0 View

How to get discharge capacity of a bole well?

No data regarding radius of influence is provided and no pumping test data available.

10 July 2024 7,168 0 View

How to apply an external electric field in gaussian 16 or Material studio DMOL3 ?

I need to apply an external electric field to 4-hydroxybenzoic acid to compare the molecule's reactivity descriptors. Could you guide me on how to apply the electric field using Gaussian and...

01 July 2024 4,192 3 View

How can I precipitate a protein from condition media ?

So I want to see is the level of a secreted protein in the condition media via western blotting What my doubt is 1. How much cells should I seed and what should be the volume of condition...

19 June 2024 1,927 1 View

Ni-NTA protein purification - how to obtain higher yield concentration?

Hello, I am trying to purify a 6X-His tagged protein using Ni-NTA chromatography. However, I obtain very less yield & concentration; and considerable protein in load flow through. Any...

16 June 2024 5,876 5 View

In sds page and western blot, non specific expressed protein with very thin band is also there along with thick band of specific protein. why ?

Asper discussion, First time my clonning was failed becuase the first 45 nucleotide was not cloned in pet30 a vector then I choosed the different clone of 1:1 ration fraction, I got the size of...

13 June 2024 7,564 7 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View