How can I fix a composition for an aluminium composite material?

10 March 2014 0 560 Report

Aluminium as a base material and copper as a reinforcement. So as to study the properties and to suggest the uses depending on the properties obtained after conducting the mechanical and thermal properties test.

Badges
Science topic

More GURURAJ D GOKAK's questions See All

RE: Relax calculation in Quantum espresso?

No convergence taking place even after several iterations. I am trying to relax Ni (111) and Ni (110). It would be great if anyone can suggest me correction in the input file. Please find the...

17 December 2023 6,438 2 View

Calculating accmulated plastic strain ?

I am modeling cyclic plasticity with a plane strain condition, a strained controlled test. I am using the von Mises yield criterion and linear isotropic hardening. Using a two-step return mapping...

25 June 2023 8,662 1 View

For analyzing isolation by distance using dbRDA analysis, do we have to perform PCNM on the response variable (Example: genetic matrix)?

I am analyzing the influence of geography and river basin on gene-flow of an endemic frog. I am interested in performing dbRDA. I am using an individual based genetic matrix. I understand that we...

11 October 2021 7,883 1 View

List of nucleoside analogs used as antivirals?

I am looking for a comprehensive list of nucleoside analogs, which are approved by FDA and EMA as antivirals. Could somebody point me to a source where can I get it? Or what would be a search...

15 May 2020 371 0 View

May I know how to run BAPS software for genetic structure analysis?

I converted my genepop file into BAPS file using CREATE. I have read the manual yet unable to understand how to proceed further. Any recommendations would be helpful.

20 April 2020 6,352 1 View

In sandwich ELISA, whether the coating antibody and primary antibody should be raised from different species or should belong to the same species?

Suppose the coating antibody (may be against some pathogen affecting chicken, for instance Newcastle disease virus i.e anti-NDV IgG from chicken) used in the sandwich ELISA is raised in chickens,...

12 December 2017 4,028 3 View

BDV VALUE OF transformer oil

Is it possible to determine BDV value of transformer oil with the help of correlation not the experiment value If sio What are the different correlations for calculating theoretical BDV value...

11 July 2017 6,527 0 View

How to measure VISCOSITY of nanofluids?

Kindly share the image and working principle of the instrument for the same? a. Shear strain method b. Can I use redwood viscometers? Thank you

25 January 2017 3,622 1 View

Is there a simplest way to raise antibody against synthetic oligopeptides?

I have synthesized an oligopeptide of 12 amino acids length, which is an immunodominant region of a larger antigen. I just want to know, if there is any simple protocol to raise polyclonal...

04 April 2016 5,152 5 View

Why in few cases at modified electrodes CV potentials shifts towards positive side with increase in current

(Why redox peak currents are increasing with positive peak potential shift). I have checked many papers on surfactant modified electrodes by immobilization. In all those papers redox currents are...

16 February 2016 3,430 3 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal?

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice

04 August 2024 7,367 3 View

Are authors sowing for scientific Journals to be reaping the benefits? We are charged for publication but we offer free peer review services, why?

As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....

03 August 2024 7,304 2 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View