Hello, I am looking for an instrument/device to measure the power (the electric field) in broadcast station, what is the name of the device used?

More Balsam Huta's questions See All

Which one of the flowing materials reflect the visible light more efficiently?

Hello everyone. Please, which one of the following materials can reflect the visible light more efficiently : semiconductors, insulators, metals or dielectric materials and why ?

24 February 2020 4,629 4 View

Mammography imaging modality?

Does the advanced mammography have the ability to change the type of the used filter according to the type of the breast density (dense or non-dense) in one machine today? Can this property...

06 November 2019 6,695 3 View

How to prepare a single and poly crystal thin film from raw polymer?

Please, I want to know about: How to prepare a single and poly crystal thin film from raw polymer? I wish I could hear also the new methods to prepare a single or poly crystal thin film from...

02 December 2018 2,969 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

How to get better phase shift in C-V curves for ferroelectric devices?

I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...

16 February 2021 8,514 2 View

What are the popular techniques for pre-processing measurement data in Smart Grid/Power System?

The data collected from various measurement devices often contains erroneous values - such as noise, missing values, etc. What are the popular techniques for pre-processing measurement data in...

14 February 2021 4,642 2 View

What can I do to keep magnetic beads suspended in solution within a syringe?

I'm looking for ways to prevent the settling of magnetic beads in solution. I have been using a syringe pump to inject a suspension of magnetic beads in PBS into a microfluidic device, and so far...

09 February 2021 6,206 2 View