the research work is about creating incision using surgical scalpel then welding of the incision was achieved by laser irradiation, I need to know how should I calculate the closure index of the incision
It is closed surface area ratio to the whole surface
Thank you very much I am grateful to you
biofilm
31 May 2024 1,969 4 View
About deficiency of calcium
24 May 2024 9,263 2 View
powdered fibers or completed fibers(without being crushed and grinded)
17 October 2021 5,091 13 View
Hello everyone. Please, which one of the following materials can reflect the visible light more efficiently : semiconductors, insulators, metals or dielectric materials and why ?
24 February 2020 4,917 4 View
Hello everyone, I have some questions about the stenosis in arteries and veins. What is the limit pressure that forced the artery to be closed causing sever stenosis? & What is the limit...
01 December 2019 1,793 2 View
Hello everyone, Please, I have a question about CT scanners Why is CT scanners available with different energies? What is the benefit behind using the CT scanners with different energies ? Is it...
28 November 2019 5,192 2 View
Does the advanced mammography have the ability to change the type of the used filter according to the type of the breast density (dense or non-dense) in one machine today? Can this property...
06 November 2019 6,944 3 View
Please, I want to know about: How to prepare a single and poly crystal thin film from raw polymer? I wish I could hear also the new methods to prepare a single or poly crystal thin film from...
02 December 2018 3,105 3 View
I am going to investigate the electric field strength in broadcast station due to some complain concerning the health situation of the employees. Thank to everyone that can help.
17 March 2018 4,273 3 View
Is it safe to be ingested? And how can I get rid of the stain? Is Lawsonia inermis toxic and should not be used in vivo? And can I separate the stain from the component that cause therapeutic effects?
31 October 2013 9,903 2 View
i am unable to interpret why its increases in start as shown in figure
11 August 2024 2,179 1 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,894 2 View
I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...
05 August 2024 3,290 1 View
There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...
27 July 2024 7,168 2 View
Though much literature suggests fitting a Voigt profile on a LIBS peak, is it also possible to fit a Gaussian profile on the LIBS peak? I have 204 spectra files, and I am building a pipeline for...
23 July 2024 6,127 1 View
I would like to use biofilmQ to analyse confocal laser image, how can do?
16 July 2024 7,628 2 View
Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?
10 July 2024 8,763 0 View
Hello ! I would like to do band structure calculations of perovsikites materials with quantum espresso. For this I installed the Intel Fortran compiler. This is what I get when I run the...
08 July 2024 1,207 0 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
Hi Dear All I would like to simulate a mode locked semiconductor laser. Does anyone know what is the best software to do it?
06 July 2024 1,648 4 View