Hello everyone!!!Any idea about how to place weight on a 100 micron gate length for sensor application?

10 October 2017 0 3K Report

Any idea about how to design mechanism to place weight on a 100 micron gate length for pressure sensor application?As the channel area is 40000 sq. micron and I have to apply a weight on this channel to be used for sensor applications

Badges
Science topic

Similar topics
Methodology
Sensors

More Kapil Bhatt's questions See All

How the conductivity of Graphene/Graphite can be measured?

Dear all please suggest, how the conductivity of Graphene/Graphite can be measured

10 November 2019 9,850 5 View

Can the capacitance of a Graphene based FET can be calculate via CV charge discharge method?

As in case of capacitance calculation for super-capacitor the CV charge discharge method is popularly used. Can the similar method be implement to calculate the capacitance for graphene based...

07 August 2019 7,325 6 View

How to get 4-5 nm layer of oxide on any metal layer at normal laboratory conditions and room temperature?

I tried to get the 4-5 nm layer thikness of any metal oxide layer on glass/ silicon but thickness was sufficiently high and the required value was not achieved. Please help me out in this regard

05 June 2019 7,377 1 View

Can anybody help me figure out which material does this XRD reflects?

Can anybody help me figure out which material does this XRD reflects? Is it Al AL2O3

11 December 2018 3,003 9 View

Why heavy particle decays more rapidly inside a barrier than that of a light particle?

It is the first time i have heard about the heavy and light particles of an oscillating wave inside a barrier if it is so? Then is there any answer to what are heavy and light particles inside a...

04 May 2018 4,692 0 View

What is difference between band bending and band lowering?

In Schottky emission the band is lowered due to application of externally applied electric field to thermally activated surface.However generally when a metal surface in brought in contact with...

03 April 2018 5,451 5 View

How to take electrical characterizations of Graphene based FET as UV sensor?

How to take electrical characterizations of Graphene based FET as UV sensor? I have following details for the same!!! For the proposed application, to my understanding from the literature...

01 February 2018 6,349 0 View

Why the Electron Mobility is low than Hole Mobility in Graphene?

Why the Electron Mobility is low than Hole Mobility in Graphene especially in graphene based FET. For more information please refer to below articles. 1. Silvestre, Ive, Evandro A. de Morais,...

31 December 2017 2,414 1 View

What is difference between optical and electrical conductivity of graphene ?

In order to simulate Graphene based patch there is requirements of many parameters in HFSS OR cst ETC. softwares. What will be the value of conductivity is to be taken for graphene in HFSS for...

11 December 2017 5,035 0 View

Can anybody help me regarding, I have got the Raman spectra of my fabricated Graphene Ink but could not able to get the peaks details?

I have fabricated the Graphene based Ink , can anybody help me regarding to understand me the Raman spectra of my fabricated Graphene ink? Image of data is attached here with

11 December 2017 8,685 4 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View