Hello, can some one have a tutorial of ANSYS fluent of multiphase flow(mixture model)?

15 April 2024 0 616 Report

Hello, could someone provide a tutorial on ANSYS Fluent for multiphase flow, covering both the mixture model and the VOF model? I need to conduct a simulation for a diphasic flow for spraying Nozzel

Badges
Science topic

Similar topics
Mathematics
Algebra
Matrix

More Oualid Elidrissi's questions See All

How to export a trained pytorch fully connected model to Matlab or Simulink ?

I have trained a fully connected model with two layers using pytorch framework, I would like to use the trained model in Matlab for possible deployment in target hardware.

09 August 2020 6,883 3 View

What is the best soft for forward modeling in ground penetriting radar systems ?

good morning what is the best used software in forward modeling for ground penetriting radar systems

28 June 2019 8,675 6 View

How to predict the velocity distribution of a sprayed powder from a nozzle?

Hello everyone, I am searching if it exists any formula used for predicting a velocity distribution of injected solid particles in my case I used flour and the type of injection is through a...

12 June 2019 6,147 3 View

Is there any method (green one) to produce SrCO3@NiO nanocomposites?

17 March 2019 6,377 4 View

how to detect the loss of the quantity of 4-Nitrophenol non-reduced to 4-aminophenol using UV-visible spectra?

Dear all; How to detect the loss of the quantity of 4-Nitrophenol non-reduced to 4-aminophenol using UV-visible spectra. Thank you

15 April 2018 5,420 3 View

How can we analyze defect structures of ZnO using UV-Visible techniques?

Dear all How can we discuss defect structures of ZnO using UV-Visible techniques? Thank you

15 April 2018 6,157 3 View

How can we detect metallic silver / Silver oxide using SEM Observation?

10 February 2018 6,529 3 View

Which flow should I choose in the case of two parallel plates ?

Hello everyone, I am a little confused into choosing the right flow's nature wether it is Laminar or Turbulent and in my case I have the Fluid flow and particles are moving through two parallel...

03 February 2018 5,865 7 View

Does the term of Dynamic Viscosity exist for solid materials?

Hi there everyone ^^, I need some help for my study in the field of Fluid flow, I use COMSOL Multiphysics for this and When I add some solid materials like copper or aluminium for the geometries...

15 December 2016 3,259 15 View

Can I use pLySs or pLysE plasmid to transform my gene of interest?

Hi everybody, I want to co transform 2 genes that are in different plasmids into one Cell, they are both in a same plasmid, so if I do they are incompatible (they have pBR322 ori) So I need to use...

20 August 2016 8,196 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View