good morning
what is the best used software in forward modeling for ground penetriting radar systems
There are many of them such as GPRSIM and the rest, but i think you can write your own programming code (using Python, C++ or Java) which will be an outstanding research work.
thanks mr kehinde but how
I think MATLAB may be a good choice. Anyway, please check the following:
https://www.researchgate.net/publication/317563768_Forward_Modeling_of_Ground_Penetrating_Radar_for_the_Reconstruction_of_Models_Response_Profiles_using_Synthetic_Data
https://www.researchgate.net/publication/236902011_Modelling_Ground-Penetrating_Radar_by_GprMax
https://www.huntergeophysics.com/product/gprsim-ground-penetrating-radar-simulation-software/
https://dl.acm.org/citation.cfm?id=1296595
thank you so much ms noha contrubing in this discussion
You can use MATGPR, Madagascar or MATLAB. They will do the job
Thank you s much
Hello, could someone provide a tutorial on ANSYS Fluent for multiphase flow, covering both the mixture model and the VOF model? I need to conduct a simulation for a diphasic flow for spraying Nozzel
14 April 2024 656 0 View
I wanted to calculate the drag coefficient of a car I designed, but the continuity only reached 0.01. This impacted the drag coefficient that I aimed for. What should I do to increase the accuracy...
13 April 2024 8,630 2 View
good evening I want to use lithmod 3D code for geodynamic modeling but it dosen t work with windows plz any suggestions for this thanks best reguards
26 October 2023 5,994 0 View
Hi everyone I am running a coupled Eulerian-Lagrangian simulation (CEL) using Abaqus_explicit. The aims of the model is to simulate the pipe soil interaction and to compute the axial resistance. I...
09 August 2023 3,035 0 View
I have trained a fully connected model with two layers using pytorch framework, I would like to use the trained model in Matlab for possible deployment in target hardware.
09 August 2020 7,080 3 View
when studying the effects of SiO2 / Al2O3 and Na2O / Al2O3 molar ratios on geopolymers. in the calculations we introduce the total quantity of SiO2 and Al2O3 contained in the precursor or only the...
16 October 2019 4,206 2 View
Hello everyone, I am searching if it exists any formula used for predicting a velocity distribution of injected solid particles in my case I used flour and the type of injection is through a...
12 June 2019 6,330 3 View
Is there any method (green one) to produce SrCO3@NiO nanocomposites?
17 March 2019 6,597 4 View
Hi all, I am looking for a paper where I can find the growth of titania at the lowest temperature below 100 ° C. Thank you
30 July 2018 3,294 2 View
How to calculate the anatase / rutile molar ratio using XRD analysis??
09 May 2018 4,197 3 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View