Hello all, I'm having a problem with surface injection of nanofluid in discrete phase model . In injection I couldn't able to add al2o3 as a material?

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Can chitosan alone can act as a reducing agent for Cu(0) nanoparticle sythesis?

[Synthesizing Cu nanoparticles without using chemical reductants]

01 March 2021 8,359 1 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

Rohan Vijay Sawant

You can replace the properties of anthracite with Al2O3. Mostly it will ask for the density. Ajay Gunti

Ajay Gunti

Rohan Vijay Sawant Thank you

Dnyanesh Mirikar

You can replace the properties as Rohan Vijay Sawant suggested or create a new material from the materials window (by selecting any existing material a new window will pop up).