Can anyone help me in finding the DTI image of the axonal track of the brain?

Hi; I need Diffuse Tensor Imaging of the brain, Not just human, any available animals image, Can any one introduce me good source for finding these files? Thanks Shabnam

03 April 2019 4,952 2 View

Best Way of measuring angular acceleration?

Hi; I am going to measure the angular acceleration in the dummy head form, I am wondering to know what is the best way for measuring angular accelerations? 1- NAP system (combination of nine...

01 February 2019 6,880 8 View

How can I call other programs in MATLAB?

Hi; I want to link Ls-prepost and MATLAB for gathering some data and running Cfile in Ls-preporst. I will be appreciated if anyone can help me about it. Best regards; Shabnam

31 December 2017 9,003 7 View

Can anyone suggest me a good book, manuscript, open course lecture in continuum, elasticity, and plasticity?

07 August 2017 1,474 2 View

Does anyone know if there is a possibility to get WSS result in CFD analysis of ABAQUS?

HI; I need some wall shear stress (WSS) during CFD analysis of ABAQUS. Is there any possibility for providing these results during CFD analysis? How? With best regards; Shabnam

05 June 2017 1,858 2 View

Can anyone suggest me any website for downloading DICOM files?

04 May 2017 8,403 20 View

Can anyone suggest me any appropriate resources for Learning MIMICS and 3Matic?

Hi I want to create some 3D geometries from Dicom files, and for this matter i prefer to use Mimics, and 3matic, Can anyone suggest me appropriate resources for learning these...

05 June 2016 5,510 5 View

Acceptable percentage of Jacobian error and warpage error during FEM impact analysis?

Salam, What percentage of brick elements can contain errors, such as warpage error (criteria 10), aspect ratio error (criteria 5), Jacobian error (criteria 0.64), min angle error (criteria 45...

03 April 2016 4,233 3 View

What is the best software for creating Hexahedral meshing?

03 April 2016 599 18 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View