GPC analysis of polymer-magnetic nanoparticles conjugates ?

More Khaki Khak's questions See All

On what basis do we select a appropriate model in Life Cycle Assessment software?

I have synthesized a membrane and used for separation CO2/CH4, now I'm going to investigate of productive impact on Environment with Life cycle assessment attitude via SimaPro software, On what...

14 September 2019 2,719 2 View

Ceria XPS Ce3D spectrum ?

Dear All, I have got the Ce3D spectra of different nanoparticles samples. There are total 12 peaks after deconvolution but literature and recent publications are showing total of 10 peaks. Could...

07 January 2018 4,737 2 View

How to achieve 100% removal of oleic acid (capping agent) from nanoparticles surface?

Oleic acid is used as a capping agent to control growth and agglomeration of nanoparticles ( cerium oxide nanoparticles). I used different organic solvents( ethanol, DMF, Heptane, Hexane, acetone...

19 April 2016 9,886 10 View

Which best statistical technique can be used on a Point reading of a static data in order to analyse the effectiveness of a particular treatment?

Say for example we are trying to evaluate the impact and effectiveness of a particular poverty alleviation programme where no comparison group is available. We are looking at a data that has to be...

28 June 2015 214 5 View

On what basis do we select a appropriate model in Life Cycle Assessment software?

I have synthesized a membrane and used for separation CO2/CH4, now I'm going to investigate of productive impact on Environment with Life cycle assessment attitude via SimaPro software, On what...

01 January 1970 789 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Alexander Pud

First you need to completely separate the polymer from the magnetic nanoparticles, then try to dissolve this polymer in a suitable solvent and then try GPS

Kuldeep Singh Chauhan

you should contact Amil-Malvarn Laboratory New Delhi, I think you would find better characterization likely to your sample.