GO on FTO coated glass photoluminscene ?

More Muhammad Jawad's questions See All

Does anyone know the JCPDS card No. of Graphite, graphene oxide for XRD analysis?

I need XRd paterrn (JCPDS card No.) for analysis of graphite, graphene oxide, reduced graphene oxide? Please provide me, if anyone have these.

10 November 2018 9,462 1 View

Why i can not get Graphene oxide peaks on FTO glas?

i have deposited Graphene Oxide on FTO glass with conc. 0.25 mg. 0.5 mg, 0.75 mg. , 1 mg, and 1.25 mg per 1mL. After that i have deposited gold nanopartilces on graphene oxide via spin coating...

06 July 2018 2,260 2 View

How can i filter Reduce graphene oxide??

i have made graphene oxide by improved hummers method. out of this i have taken 100 mL GO and then i have add 2 g NaBH4 at 80 degree for 1hr. But after this i can not filter it by filter paper....

04 May 2018 3,081 0 View

Interaction of Graphene oxide/ Au NPs prepared in organic media?

I making a composite of GO: Au NPS. i have disperse graphene oxide in organic solvent like NMP, DMF. and Gold nanoparticle in organic media where i am using formaldehyde, cyclehexane and...

01 February 2018 4,398 0 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View