Why i can not get Graphene oxide peaks on FTO glas?

More Muhammad Jawad's questions See All

Does anyone know the JCPDS card No. of Graphite, graphene oxide for XRD analysis?

I need XRd paterrn (JCPDS card No.) for analysis of graphite, graphene oxide, reduced graphene oxide? Please provide me, if anyone have these.

10 November 2018 9,462 1 View

GO on FTO coated glass photoluminscene ?

When I deposit graphene oxide on fto coated glass with quantity 0.25mg 0.5mg 0.75mg and 1mg per 1ml each by spin coating at3000rpm and anneal it at 100c for 10 min.Then i did photoluminscene...

08 September 2018 7,695 3 View

How can i filter Reduce graphene oxide??

i have made graphene oxide by improved hummers method. out of this i have taken 100 mL GO and then i have add 2 g NaBH4 at 80 degree for 1hr. But after this i can not filter it by filter paper....

04 May 2018 3,081 0 View

Interaction of Graphene oxide/ Au NPs prepared in organic media?

I making a composite of GO: Au NPS. i have disperse graphene oxide in organic solvent like NMP, DMF. and Gold nanoparticle in organic media where i am using formaldehyde, cyclehexane and...

01 February 2018 4,398 0 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

Rafael Valentin Tolentino-Hernandez

May be due to the thickness of your film, in a thinner thickness is more complicated see the graphene oxide (GO) peaks, or may be your deposition technique for GO in not working properly, yuo can also run a Raman analisys in order to check the formation of GO film on FTO substrate.

Muhammad Jawad

Thank you so much for your kind response @Rafael Valentin Tolentino-Hernandez