For contact stress analysis in gears, which stress in ANSYS represents contact stress, whether to use Von mises stress or contact pressure?

More Ankush Choudhary's questions See All

How to do buckling analysis in ansys apdl for laminated plate with PZT 5H attached?

I am doing buckling analysis of laminated plate surface bounded with two piezoelectric PZT 5H and axial compressive load is applied. I am getting an error, No ANEL table exists for material 2....

16 February 2021 510 1 View

What to do if I am doing a Meta Analysis of Exploratory studies and the studies do not have effect size??

I am doing a meta analysis of imaging exploratory studies which themselves did not have effect size. Therefore, I am unable to compute the variability in the effect sizes in my meta analysis. What...

18 January 2021 4,881 4 View

In multi-label classification, why the sample-based performance evaluation metrics are usually lower than the label-based performance metrics?

Hi all, I am doing a multi-label classification using machine learning algorithms. In order to evaluate the performance of the multi-label classification, I am using label-based and sample-based...

13 January 2021 7,590 3 View

In multi-label classification, how do we find the P values and confidence interval for the performance evaluation metrics?

Hi all, I want to report the P values and confidence intervals for AUC values for two different multi-label classifiers. I got the following article, which is applicable for a binary...

10 January 2021 2,217 3 View

What are the approaches of improving SNR of spaceborne Hyperspectral instrument for Earth observation or Planetary science missions?

Spaceborne Hyperspectral observation (i.e. hyperspectral remote sensing in uv-visible-infrared spectral range) of Earth and for Planetary science, plays a very important role in improving...

27 December 2020 453 2 View

How to extract and store elemantal strain results data of a FEA using ansys in a text file for postprocessing?

I am doing a bone remodeling simulation using ANSYS. i need to extract elemental strain results and store in a text file for further processing. There is no option using *GET and *VGET command...

15 November 2020 2,731 2 View

How can I obtain Nodal Forces at selected nodes/elements for all time steps in a transient analysis in ANSYS?

I am working on a transient structural analysis in Ansys Mechanical. I want to export the Nodal reaction force vectors for selected nodes of a part at all the time steps. Basically, I need a force...

18 October 2020 9,789 3 View

I could not find a publication that fits the idea of evaporation together with DPD. Any suggestions?

I did find some papers that incorporate the two ideas together but I could not follow the research methodology. The simulation results were remarkable but not self explanatory. I tried to follow...

20 September 2020 5,354 4 View

Are there effective measures to prevent substantial economic loss due to blister beetle (Mylabris pustulata) in early pigeonpea?

Pigeonpea is a preferred host to adult blister beetle (Mylabris pustulata). Early pigeonpea, which is sown during May 15-June 15 in North West and north east plains of India, enters into flowering...

28 July 2020 1,278 8 View

Whether application of data science is equally important in agriculture including crop improvement??

In recent years, data science has emerged as a promising interdisciplinary subject, and helped understand and analyze actual phenomena with data in multiple areas. The availability and...

08 June 2020 6,514 6 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View