How to run a program opensees Linux from python ?

08 September 2017 9,966 1 View

How to extract the desired signal from the following combination?

A given receiver has received the signals in the graph. It is aimed to extract the red signal. Is there an idea for that?

07 August 2017 9,393 1 View

When and why does nucleus engulf mitochondaria?

In our study using a herbal extract in a large dose, we found that the nucleus engulfs the mitochondria in cardiac myocyte of rat in a way similar to phagocytosis. All heart injury markers and...

11 December 2016 7,637 7 View

How to apply gravity weight load during abaqus explicit using euler mesh?

Since the Euler grid is only used in dynamic explicit analysis, the first gravity load step is also solved by this method. The gravity load is applied to the model very slowly during the first...

05 June 2016 3,043 0 View

How to Extracts the maximum result from an Abaqus odb ??

i mean maximum result through all values during step time, is there any script in abaqus can do this ??

05 June 2016 1,268 0 View

In seismic analysis of tanks , are we have to consider parameters of cycle hardening in abaqus ??

in nonlinear analysis , what i do before is define only elastic and plastic stress vs strain and define fracture point value , yesterday i read this paper and found that there is also parameters...

04 May 2016 8,652 1 View

Is that really or it is error in modeling in abaqus?

tank stiffener get yield and reach to failure before tank wall under static or dynamic load using Coupled Euler Lagrangian (CEL) method in abaqus

04 May 2016 8,273 4 View

What is similar to Link element (LINK8) that was used in ANSYS to model the seismic isolation system in abaqus ??

model isolated tanks in abaqus

03 April 2016 7,376 2 View

What is the reason for that message in abaqus ??

02 March 2016 3,686 6 View

How to perform buckling analysis of a cylindrical shell with a fluid flow using Fluid Structure Interaction in abaqus ??

02 March 2016 8,770 1 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View