I want to know is there any MATLAB code for topology optimization of shell structures???
I am comparing solutions of linear elastic response of a material in Abaqus explicit with inbuilt model and with VUMAT (Linear Elastic) code on single element. I am getting almost same results...
08 September 2019 8,296 2 View
I am doing fatigue damage analysis of composite in Abaqus. How to simulate high number fatigue say 10K or 20K cycles in abaqus, since it is not feasible to simulate each cycle due to high...
04 May 2018 1,026 2 View
I have created .RPT in Abaqus but when I open the file it doesn't contain any proper data and most of the columns have NO VALUE. I would be thankful if anyone can provide the procedure to export...
06 July 2017 1,220 13 View
In research articles term 'normalized stress' or Normalized modulus is frequently used. What is normalized stress or modulus? And what is its significance?
31 December 2016 6,290 0 View
looking for design guidelines of striker mechanism or gas gun mechanism of split hopkinsor pressure bar. what are the parts of launching system and what instrumentation is required?
10 November 2016 8,606 0 View
some study material for FEM of ceramic matrix composites
09 October 2016 2,804 2 View
can anyone suggests procedure to perform FEA of ceramic matrix composites?
09 October 2016 3,560 3 View
how to define orientation of layers and what should be thickness of cylinder?is it equal to thickness of layers? what should be boundary conditions when internal pressure is applied?
04 May 2016 5,222 5 View
plate dimension 100*100mm, material graphite/epoxy, stacking sequence (0/90/0/90/0/90/0) ply thickness=1/7, total thickness of laminate=1mm , applied stress=1MPa, but after solving the problem...
04 May 2016 5,259 5 View
what is the meaning of 95,181,281 in SOLID95, SHELL181 and SHELL281?
04 May 2016 6,850 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!
08 August 2024 6,242 2 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View