Fiber Bragg Grating Design Video?

Sorokhaibam Nilakanta Meitei @Sorokhaibam_Meitei

10 October 2018 0 10K Report

Is there any video or lecture about Designing of Fiber Bragg Grating in COMSOL Multiphysics

Badges
Science topic

More Sorokhaibam Nilakanta Meitei's questions See All

How to generate a spherical pressure wave from a source point in COMSOL Multiphysics software?

How to generate a spherical pressure wave from a source point in COMSOL Multiphysics software.

10 November 2019 7,578 1 View

Can consider a sinusoidal wave as a Partial discharge acoustic pressure wave?

Can consider a sinusoidal wave as a Partial discharge acoustic pressure wave.

08 September 2019 2,697 2 View

The amplitude of frequency in FFT doesn't match time-domain amplitude in COMSOL Multiphysics software?

Dear friends I am designing a underwater optical acoustic sensor Using COMSOL Multiphysics software. I would like to analyze the received signal signal by sensor in both the time domain and...

07 August 2019 2,806 3 View

How to export matlab program file to COMSOL?

03 April 2019 6,481 2 View

How to calculate the sensitivity of the acoustic optical sensor?

Dear friends, I am modelling an optical based underwater acoustic sensor to detect the acoustic sound wave which is induced inside the water-filled tank using COMSOL Multiphysics software. Due to...

03 April 2019 5,171 4 View

How to used contituity boundary condition in an acoustic wave propagation in an oil filled tank using COMSOL Multiphysics?

How to used contituity boundary condition in an acoustic wave propagation in an oil filled tank using COMSOL Multiphysics

11 December 2018 6,592 1 View

How to convert the output voltage(Volts) of Piezoelectric sensor into pressure (Pascal)?

Dear friends, I am working on an application where I need to convert the o/p voltage(in volts) of Piezoelectric acoustic sensor into pressure (in pascals). I wanna know how I would be able to do...

11 December 2018 5,215 8 View

Can used Piezoelectric transducer as an acoustic wave signal receiver sensor?

Dear friends, I am going to design a piezoelectric transducer as an acoustic wave signal receiver sensor using COMSOL Multipysics. Description of the model: In an air-filled rectangle box an...

11 December 2018 1,204 8 View

How to convert the output voltage(Volts) of Piezoelectric sensor into pressure (Pascal)?

Dear friends, I am working on an application where I need to convert the o/p voltage(in volts) of Piezoelectric acoustic sensor into pressure (in pascals). I wanna know how I would be able to do...

11 December 2018 5,195 8 View

2D model of optical Fiber Bragg Grating sensor using COMSOL Multiphonics?

Dear friends, I am going to desing an optical Fiber Bragg grating sensor for pressure and strain measurement using COMSOL software. But, I am new in this software so if anybody having any idea...

11 December 2018 9,015 0 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View

Look for qualified candidates of Visiting Scholars to Southwest Jiaotong University?

We invite qualified candidates of Visiting Scholars to engage in research collaboration or deliver lectures on their research, with travel expenses covered. The visiting period is flexible,...

20 July 2024 1,165 1 View

Can anyone help with this comsol error? Pleaaaase I need help !!?

Undefined variable. - Variable: comp1.cNa - Géométrie: geom1 - Domaine: 1 Failed to evaluate expression. - Expression: comp1.cNa - Affichage: Graphique sur ligne 1

19 July 2024 1,938 2 View

Why electrical charge on the moving plate increase?

Hi, everyone This figure depicts a simulation of an electrostatic energy harvesting system in COMSOL Multiphysics software. My question is regarding the relationship between the changes in...

19 July 2024 4,694 4 View

Why does the error "The relative error (0.29) is greater than the relative tolerance" appear in Comsol Multiphysics?

Hello, My name is Radu Jubleanu, I am a PhD student at the Politehnica University of Bucharest. I work in the field of magnetic storage in superconductors. I want to carry out a numerical study of...

15 July 2024 6,025 1 View

How to use stress and displacement results from 1st stationary simulation as initial conditions for 2nd eigenfrequency simulation in COMSOL?

Dear All, I am trying to define the dispersion curves of a periodic unit cell in COMSOL Multiphysics with prescribed displacements. I am using two separate studies: - Study 1: Stationary, with...

13 July 2024 7,855 1 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View

How to solve Bubble Error in fiber splicing?

I'm having a bubbling error while splicing 100/350 um optical fiber (core/cladding) on the Fujikura FSM100P+. I have tried some ways such as changing Prefuse power and Prefuse time but to no...

03 July 2024 7,463 6 View