Facing a syntax error problem wile running brig with genbank file what's the solution?

06 August 2023 0 6K Report

I am facing a problem while running brig with genbank files. I want to give gene annotations & following the manual I have added the genes with the start & stop codon mentioned. But after running couple of times, I am facing same syntax error. Please give a solution

The picture is attached below

Badges
Science topic

More Priyanka Basak's questions See All

Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,746 4 View

CHO-K1 suspension adaptation protocol?

I am trying to adapt adherent CHO-K1 cells in F12K+10%FBS to suspension culture in only F12K, but in vain. I have followed Mirus bio as well as Thermo protocols, please suggest any alternative....

31 July 2024 3,756 0 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

Why cannot i find my protein on cell surface after antibiotic selection of expressing plasmid?

I cannot confirm cell surface protein expression by flow cytometry even after transfection and antibiotic selection of cells. Does it take long for proteins to express on the cell surface? the...

28 July 2024 3,178 3 View

When making abraxane with Nab tech, why is 9:1 Chloroform&EtOH used as solvents?

Is it the best optimization ratio based on experiments?

22 July 2024 8,170 0 View

Can diamond be grown using molecular beam epitaxy?

22 July 2024 9,755 2 View

Can anyone suggest the specification of the test tube used for the tube adherence method for biofilm assay?

when we grow biofilm in test tube, the pipette often do not reach near the content. so we have to decane it directly or use a smaller test tube.

17 July 2024 3,532 0 View

How can I use LabVIEW to control of an ethernet-based driver?

Hello everyone, I am new to LabVIEW, right now we need to control the movement of an ethernet-based stage drive. We got the sample code from a collaborator but their instrument is USB-based, so we...

11 July 2024 5,385 2 View

Systematic review meta-analysis paper?

Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...

10 July 2024 5,490 5 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How do I run a dead well test for a QuantStudio 5 qPCR machine?

I am preparing to run a lot of samples on a 384 well plate and I wanted to test if any well in my PCR machine is dead so as not to lose any data. I would really appreciate help with how I can do...

24 July 2024 8,172 1 View

VECM Model: Positive/insignificant CointEq1 ?

Hello everyone, I am conducting

22 July 2024 8,085 11 View

Merge Intensity Data from 2 runs?

Hi, We have collected several images for two independent runs of an experiment using two different confocal microscopes and settings. Thus, the intensity values collected through ImageJ were...

22 July 2024 8,722 0 View