Estimate seismic green's functions?

28 April 2019 1 2K Report

How do you estimate then apply the green's function for set of seismic sensors, especially for surface waves and near field perturbations? I want to construct the Green's functions from a set of seismic measurements for nearby traffic .

Marty Distasio

Habib,

Thank you very much for this info. I will review it and see if I can apply it tpo an area I am investigating - this is good, appreciate it.

Badges
Science topic

More Marty Distasio's questions See All

Is there a rapid colorimetric determintaion of oxalate for crops?

Colorimetric methods (UV-Vis) used to estimate oxalate content on crop fruits

17 April 2016 5,877 2 View

Are professors in higher education institutions mostly intrinsically or extrinsically motivated to perform research and teaching?

It is often mentioned that scientists or professors at universities do not need to be motivated by material incentives to do their work. As a result, classical incentive schemes as found in...

03 September 2012 5,067 34 View

Quantum mechanics determinism vs probabilist theory

Does the quantum mechanics gives probabilistic results or exact quantified values?

01 January 1970 9,029 8 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

Algorithms to filter corrective max and min from a set of data?

I've got this 5 year Direct Normal Irradiance data I downloaded from https://re.jrc.ec.europa.eu/. I ordered this by year and by every 24 hours because I need the DNI curve by max in summer, min...

17 February 2021 2,777 5 View

What should a smart water system look like?

Our team is designing a smart water C&C dashboard for a smart city initiative. As we look into the current smart water system landscape, we couldn't reconcile to a definitive solution that...

16 February 2021 1,094 3 View

Receiving very less number of hits and events in acoustic emission tests?

I am doing a three point bend test with concrete specimen of dimension 280mm*90mm*90mm. I am putting 2 sensors near the notch with 3cms away from both the sides. the experiment ran for 20 mins but...

13 February 2021 2,990 1 View

How to increase coupling range (distance between reader and sensor coils) in LC resonance circuit?

Hello great researchers, I am working on a wireless pressure monitoring project where sensing part is actually an LC resonance sensor and I am using a planar coil as a reader to get wireless...

11 February 2021 4,148 5 View

I am looking for a microbend optical sensor design...can anyone please provide me some idea about it??

I am working on a landslide model...i need an optical sensor to determine the amount of pore pressure and other values..i am thinking of using a microbend sensor. Can anyone please provide me with...

11 February 2021 5,911 2 View