01 August 2023 0 918 Report

I am working on ansys to find the acoustic response of an isotropic plate and while doing so I got an error saying that the mass source should be defined in a acoustic region, This FSI (fluid solid interface) load should be defined on a common interface of acoustic and structural regions. Please help me in sorting the errors. Below you can find the attached image of errors.

More I. Maneesh's questions See All
What indicators are suitable for measuring someone's experience?

Hello everyone, Sometimes we feel confused when we want to focus on measuring or assessing someone's experience, because someone's experience has a very broad scope, both morally and spiritually....

05 January 2021 584 3 View

What kind of detector is used in the double slit experiment to determine through which slit the photon or electron passes?

Explain exactly what the detector does and if the choice of detector affects the outcome. Einstein and Bohr had some discussions on this. What's the current situation?

29 December 2020 1,984 5 View

Can photons curve the spacetime and how would you measure this effect?

Mass bends spacetime. It's generally accepted that the photons have no mass, but they do have momentum and energy and can cause pressure, so they have equivalent mass of p/c. The...

14 December 2020 3,195 6 View

Ways to establish exchange bias in ferromagnet/ antiferromagnet heterostructure?

When ferromagnet (FM) and antiferromagnet (AFM) are coupled, exchange bias can be generated at the interface of FM and AFM which acts as a bias field in the hysteresis loop. I am particularly...

24 October 2020 8,580 1 View

How does a single H3 mutation capable of affecting the global level of H3K27me3?

In DIPG patients, one puzzle is that typically only one copy of the H3 gene is mutated. Therefore, how does one single copy of mutation affect the global level of H3K27me3, considering that there...

04 October 2020 3,578 1 View

How to calculate Lexical frequencies and Text Frequencies of phonemes and graphemes of English language?

This is so far the procedure I was trying upon and then I couldn't fix it As per my understanding here some definitions: - lexical frequencies, that is, the frequencies with which correspondences...

27 September 2020 4,742 3 View

How heat generated during friction stir welding due to friction and plastic deformation can be modeled by Abaqus?

I want to make FSW simulation By Coupled Eulerian Lagrangian (CEL) method by Abaqus software. My question is how I cane consider the heat generated in the modle step by step on Abaqus.

10 June 2020 8,428 1 View

What is the Algebra structure ?

I have proved some property. 1. Idempotency, 2. Commutativity, 3. Associativity, 4. Absorption law, 5. Distributivity and 6. De Morgan's laws over complement. what is the structure of this...

28 April 2020 9,188 4 View

How do i calculate MOS from NS2 Simulation with NS2Voip++ Traffic Generation?

Hello sir, im struggling with *.output file from ns2voip++ traffic generator. I currently working on ns2 simulation for audio communication, from ns2voip++ its generate *.output file with binary...

08 March 2020 9,357 7 View

Can anyone suggest an open source tool for Sensor error correction in Hyperspectral Image processing?

open source tool for Sensor error correction in Hyperspectral Image processing

28 January 2020 6,426 2 View

Similar questions and discussions
Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close