How to simulate Graphene with Comsol Multiphysics 5.2

02 March 2017 1,133 7 View

Could any one elaborate what does these XRD peak means?

I have deposited Graphene oxide on Cu substrate with the help of electrochemical work station with the negative voltage applied. I got 3 peaks at different range. What does these peaks means at...

04 May 2016 1,055 11 View

Is there any computational simulation software available to simulate Graphene oxide or Graphene?

Simulation software which can simulate quantity of different Graphene oxide materials and gives best solutions.

01 February 2016 7,580 0 View

What is the solubility rate of Gum arabic in DI Water?

11 December 2015 892 9 View

What is fastest facets usage means in Graphene research?

01 January 1970 9,726 0 View

How can I deposit Graphene Oxide on Copper substrate with Electrochemical workstation?

Currently, I am doing an experiment with Electrochemical Workstation (Metrohm Autolab). I am depositing Graphene Oxide on copper substrate with three electrode system with an electrolyte of GO...

01 January 1970 9,756 6 View

How to develop solar battery?

I want to develop solar battery which is the combination of solar cell and battery itself. I mean to make a single module with Graphene material and enhance the efficiency of cell and storage...

01 January 1970 6,935 4 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

Problem in detection of a specific gene & elimination of primer dimer in qpcr?

In our lab, we are trying to do real time PCR for some genes. One of them has a size of 85 bp. Whatever we do, we had an amplification in negative control. When we run agarose gel, it always a...

14 February 2021 9,750 11 View