Does anybody know about DTC of the induction motor?

13 June 2018 0 7K Report

I have two simulation about DTC (direct torque control) and FDTC (fuzzy direct torque control) of the induction motor. DTC simulation works well but FDTC simulation haven't good outputs. I've added the simulations below. Please check it and help me.

Badges
Science topic

Similar topics
Engineering
Control Theory

More Alireza Sahafi's questions See All

What do you know about classroom management?

Hello, if possible, please send me new methods of management and communication in the classroom. thank you؟

18 June 2024 4,139 3 View

How do we measure the electrical conductivity of this magnetic nanocomposite?

A magnetic nanocomposite has been synthesized and its electrical conductivity needs to be measured. What analysis and technique can be used to measure the electrical conductivity of this magnetic...

16 June 2024 7,488 3 View

Is it possible to estimate Horizontal in-situ stresses' directions and magnitudes from seismic data by using AI methods?

We know that one of the important members of a 3D Geomechanical Model is in-situ stresses' directions and magnitudes. we can use the seismic data to estimate these parameters in special record...

21 May 2024 1,332 2 View

Hello. why do we measure surface tension?

surface tension

20 May 2024 4,895 1 View

What are the S-scheme and Z-scheme heterojunctions in photocatalytic systems? for the types of heterogeneous photocatalysts, how can you determine?

what are the S-scheme and Z-scheme heterojunctions in photocatalytic systems? and for the types of heterogeneous photocatalysts, how can you determine the type of S-scheme and Z-scheme?

16 May 2024 1,545 1 View

Why is my first article being rejected fast by related journals?

Hello everyone, I hope you are all doing well. I have already checked plagiarism, related articles’ structures, and grammar, and they seem fine, but good impact factor journals that I have written...

15 May 2024 1,007 4 View

Altitude control of a quadrotor ?

hi there i'm working on quadrotor path tracking in matlab's simulink . there is an inner loop which is responsible for tracking the desired euler angles generated by the outer loop . feedback...

05 May 2024 7,705 5 View

How to perform LC-BLYP calculation with GAMESS?

Hello Dears, I am currently working on time-dependent density functional theory (TDDFT) calculations for both singlet and triplet states using the LC-BLYP functional in GAMESS. I believe I have...

01 May 2024 4,614 0 View

Does Baicalein interact with DMEM high glucose or FBS?

greetings, I'm culturing SW480 cells on DMEM high glucose gibco with FBS. When I'm performing MTT Assay, upon treatment of cells with Baicalein, the color of medium with 5% FBS changes to dark...

25 April 2024 7,115 4 View

I'm getting error:( Domain error. To compute complex results from real x, use 'sqrt(complex(x)) ) in simulink?

hi there . i'm currently working on a thesis which involves designing a fast nonsingular terminal sliding-mode controller for attitude control of a quadrotor. the outputs of sliding mode...

20 April 2024 425 2 View

An animal in not a rock (e.g., Koch 2013), it has an internal constitution that can be modified?

Vertebrates and invertebrates (e.g., arthropods: insects, crustaceans, etc.) have two different neuro-muscular systems given their differential construction: the former have an endoskeleton and...

07 August 2024 648 0 View

In WECS : Gain values for conversion of PMSM rotor speed(rad/s) to p.u. input to wind turbine and Torque(pu) of WT to input of PMSM-Torque (Nm) ?

I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...

03 August 2024 888 1 View

How are aPTT and PT values reduced after hemodialysis compared to before dialysis value in patients with chronic kidney disease?

I am conducting my research regarding blood coagulation in patients with CKD. I observed a reduction in post hemodialysis aPTT and PT values compared to pre hemodialysis values. But most of...

30 July 2024 3,467 0 View

Unexpected 35 kDa Band Observed During Expression and Purification of Dengue 3 NS5 RdRp Domain ?

Background: I am developing an RdRp assay for Dengue virus-3 and need to express and isolate the NS5 protein's RdRp domain (~101 kDa). My expression vector includes a GST tag followed by a 6x His...

13 July 2024 9,950 3 View

Intracerebroventricular (ICV) AAV inj.?

I'd like to know if anyone has got experience in intracerebroventricular (ICV) AAV inj. I am looking for a concomitant spread of the AAV including but not limited to the motor cortex and the...

12 July 2024 781 0 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

How can we calculate the polygon scanner speed by changing the supply voltage?

I am using a polygon mirror scanner that have 6 facets and the dc brushless motor speed was given 10,000 RPM. Now I want to know how to calculate the polygon speed if I change the power supply...

11 July 2024 5,942 1 View

How can I create a knee reinforcement motor in OpenSim software? Is there a ready model that I can use?

I need to put an extra motor on the knee to do part of my project. The process of doing it is needed in the use of other software and sub-programs.

03 July 2024 6,038 0 View

Can I do IPTG induction on OD600=2.6 in TB?

I have been looking at papers for protein expression and trying to follow the process. I'm using TB medium to do the process, and the paper says to grow to an OD600 = 1.8 at 37 degrees, then let...

30 June 2024 6,502 5 View

How to reduce the material coming out of the torque rheometer?

A physical mix was in vitro evaluated on a torque rheometer. The composition was predominantly recycled polypropylene (PP), yet the melt flow index (MFI) was found to be excessively high....

25 June 2024 10,154 0 View