Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Does heat in goat affected by feeding or BCS of the animal?

Does feeding affect heat in animal? if we were to add a specific feed (with data on dry matter content), how can we correlate feeding to estrus?

10 January 2021 9,719 13 View

Why the presence of surface active compound repress the mass spectra of other compound? If the sample is itself surface active, then self repression?

I am assuming the resulting insertion/agglomeration in the presence of a surfactant or the agglomeration of surfactant may reduce the rate of ionization. The mobility of the ion may also be...

07 January 2021 987 5 View

What are various Thermal Insertion Materials?

I am working on a project of heat Sink. What are different insertion / filling materials I can use? Suggest some material about it. Thankyou

28 December 2020 728 3 View

How to prepare methylcellulose based semisolid media for cell culture?

Does anyone know how to prepare methylcellulose-based semisolid media for cell culture? Which one to use 15cp or 1500cp?

10 December 2020 5,266 2 View

What are all the criteria for the occurrence of Lunar Eclipse?

I have read the maximum limit of Lunar Eclipse is 12.2 degrees of arc (i.e. the difference in the longitude between Moon and any one node of the Moon). However on on June 5th 2020, a partial Lunar...

27 August 2020 986 5 View

What is the need to run the optimization code for multiple times? What will be the outcome for this multiple runs?

Dear all, I have to know what is the need to run the optimization code for multiple times... For example, I m implementing a new variant optimization algorithm, I am setting maximum number of...

19 July 2020 6,004 4 View

Can anyone know how to do 1D ground response analysis using COMSOL multiphysics 5.4 ?

I want to compare results of 1D ground response analysis of DEEPSOIL and COMSOL

05 July 2020 3,014 2 View

No title

16 June 2020 2,168 1 View

What is the current status on regulatory approvals of COVID-19 vaccines?

What is the current status on regulatory approvals of vaccines meant for COVID-19 according to USFDA, EMA, TGA, etc?

10 June 2020 7,582 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View