Do anyone has an idea about the errors of element formulation in ansys?

Noha Elfiky @Noha_Elfiky2

03 March 2018 0 1K Report

i have put pore pressure values in each element in the model,but while solution process the following error appeared:

REASON FOR TERMINATION. . . . . . . . . .ERROR IN ELEMENT FORMULATION

could any one help me?

thanks.

Badges
Science topic

More Noha Elfiky's questions See All

What is the value if angle of dilation that should be assigned in case of liquefaction?

i am modeling asingle pile in liquefiable soil, i am confused about the accurate value of angle of dilation in such case, can anyone kindly helps me, thanks in advance.

03 April 2018 292 0 View

It is possible to assign different material properties on different nodes in ansys apdl ?

I am trying to assign shear modulus value to an element, however, the equation of it is a function of pore water pressure rise. subsequently, the value is varying for each node, how can I assign...

02 March 2018 6,796 5 View

How to restart a coupled pore fluid diffusion analysis in ansys apdl?

i am trying to restart a coupled pore fluid diffusion analysis using multi frame restart method; but after the initial run of the model, the following message has appeared : the restart command...

02 March 2018 9,448 3 View

Is it possible to get erthquake record type-shear stress time history not acceleration time history?

i want to apply an earthquake load on the soil as shear stress cyclic load in order to be able to make changes on the model after each shear stress cycle, but i can't find earthquake record in the...

01 February 2018 9,528 0 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

What are the steps of formulating a herbal extract into a sheep/goat drench?

I am working on natural remedies for de-worming in small ruminant livestocks. Part of my project involves formulation of drench-type product, which I have not much experience in. My experience is...

30 July 2024 9,806 1 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Reason for discontinuities in my Band structure?

Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...

25 July 2024 2,920 11 View