What is the value if angle of dilation that should be assigned in case of liquefaction?

04 April 2018 0 299 Report

i am modeling asingle pile in liquefiable soil, i am confused about the accurate value of angle of dilation in such case,

can anyone kindly helps me,

thanks in advance.

Badges
Science topic

Similar topics
Engineering
Modeling

More Noha Elfiky's questions See All

It is possible to assign different material properties on different nodes in ansys apdl ?

I am trying to assign shear modulus value to an element, however, the equation of it is a function of pore water pressure rise. subsequently, the value is varying for each node, how can I assign...

02 March 2018 6,796 5 View

How to restart a coupled pore fluid diffusion analysis in ansys apdl?

i am trying to restart a coupled pore fluid diffusion analysis using multi frame restart method; but after the initial run of the model, the following message has appeared : the restart command...

02 March 2018 9,448 3 View

Do anyone has an idea about the errors of element formulation in ansys?

i have put pore pressure values in each element in the model,but while solution process the following error appeared: REASON FOR TERMINATION. . . . . . . . . .ERROR IN ELEMENT FORMULATION could...

02 March 2018 1,277 0 View

Is it possible to get erthquake record type-shear stress time history not acceleration time history?

i want to apply an earthquake load on the soil as shear stress cyclic load in order to be able to make changes on the model after each shear stress cycle, but i can't find earthquake record in the...

01 February 2018 9,528 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View