Dear Sirs
How i can model closed end composite pressure vessel over warped with carbon fiber epoxy resin 4 layers stacked as [+45/-45/-45/+45] with 0.4 thickness aluminum linear vessel dia is 500mm length is 1000mm by ANSYS software
It quite easy! Create geometry and follow the stacking sequence (lay-up option in ANSYS) and assign material properties to the element.
See modelling is a global terminology , please mention what exactly you want to know ?
Following
ACP module can be used in ANSYS and stack them at your requirements or other software Helius freeware from AUTOCAD for laminate based problem solving.
Any one has an idia about the kind of jars and bowles we need for nanopowder preparation foe example using the Planetary Micro Mill PULVERISETTE 7 classic line. How to avoid contamination and to...
12 November 2023 2,185 1 View
I'am searching a mthode of multiple correspondence analysis using python,
05 December 2022 4,001 4 View
Regarding my needs I am looking for a glass coating agent that makes the glass hydrophobic permanently
09 February 2021 4,168 5 View
Hi all, Is it alright to us the χ2 test for a measure variable over time? E.g., a true-false question which is measured in two rounds of a survey ( not necessarily repeated...
16 November 2020 8,499 4 View
Dear all, When using tonyplot, I can get the I-V curve without any problems, but when I try to add small signal analysis after gate voltage sweep (ac freq=1e6) in Silvaco Atlas it shows zero Cgd...
06 October 2020 4,929 3 View
Plant parasitic nematodes and application of multiplex PCR for identification and detection...
02 February 2019 647 0 View
Please can you help me to identify this phytoplankton specie that bloom in Beni Ansar Harbor (Nador) - Mediteranean coast of Morocco? Thank you very much. Faid
16 January 2019 3,330 3 View
for my research
27 December 2017 7,162 8 View
I need to compare my work with the Reservation-Based (RB)code that described in the "Offloading Floating Car data" article. Can anyone give me the its code? I work with ns2 simulator
06 September 2017 3,763 1 View
hello everyone; i'm trying to implement lattice FIR filter and RII lattice filter in c. my question is how to make the first g(n-1), some one can help me please! i know that z-1 represente a delay...
08 June 2017 7,418 4 View
I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...
10 August 2024 3,628 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 941 3 View
How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?
09 August 2024 3,291 2 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...
06 August 2024 8,716 0 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
The starting material is a finely ground powder. Some particles contain more graphene than others.
30 July 2024 3,978 2 View
I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...
30 July 2024 6,137 0 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,031 2 View