How to transfer a CVD grown monolayer of hBN from the Cu foil to a polymer substrate?

i am looking for ways to transfer hBN nano sheets from the Cu foil used in the CVD process to a polymer substrate (PDMS or PMMA)

31 December 2019 2,144 7 View

Can anyone please provide me any evidence of using CVD grown graphene for heavy metal removal from water?

I am looking for a potential application of CVD grown graphene. I am wondering if there is any literature on it. Almost all the literature on heavy metal removal from water is with Graphene Oxide....

06 July 2019 7,031 2 View

Can anyone please provide me with a paper or book regarding the basic nucleation process of graphene on Ni substrate?

I am trying to learn how nucleation of graphene actually happens on a Ni substrate.

05 June 2019 3,732 3 View

Why the position of the XRD peak of CdS changes when I use Ni anode instead of Cu?

XRD

02 March 2019 401 1 View

Why the intensity of the XRD of CdS changes when I use Ni anode instead of Cu?

XRD analysis of CdS

02 March 2019 1,556 4 View

Is it possible to probe the conductivity of exfoliated graphene using scanning probe microscopy (i.e. cAFM) ?

I am trying to measure the conductivity of exfoliated graphene nano sheets using conductive atomic force microscopy

31 December 2018 6,686 4 View

How much energy is required to peel of a single layer graphene from bulk graphite (using liquid exfoliation)?

Graphene Exfoliation

11 December 2018 5,377 0 View

How to calculate the number of layers in nano sheets of the exfoliated MoS2 from it's UV ViS spectra?

I am trying to estimate the number of layers present in exfoliated 2D MoS2 nano sheets from it's UV ViS spectra

10 November 2018 5,303 2 View

What kind of shifting of the peak position (in the Raman spectra) of the G (1590/cm) is observed when graphite is exfoliated in few layer graphene?

I am asking a technical question regarding the Raman spectra of graphene

09 October 2018 2,438 2 View

How to calculate extinction from absorbance/tranmittece?

I am trying to measure the extinction of a solvent which contains nanomaterials.

09 October 2018 5,810 4 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

How to identify what type of fillers are in a polymer?

Hello everyone, I have some PHAs blended with fillers and nucleating agents, yet I don't know what kind of fillers or nucleating agents. The producer has shut down and there's no way to get in...

24 February 2021 1,356 8 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View