I was doing a cosimulation analysis and I met the following mistake: " Analysis cannot continue due to co simulation engine mapping search failure"
Does somebody know what does it means and how to solve it?
thanks
Hey Annarita,
I am facing the same problem and do not have a clue how to solve this Problem.
Could you solve it meanwhile?
Hi you guys,
I had this same problem and it turns out the co-ordinates were not matching in the complementary models.
So that means that the co-ordinates of the interface should be the same in each model (CFD and structural).
I hope this helps you guys!
Regards, Kyrin.
HI! I'm doing a co-simulation in Abaqus but after many steps the analysis abortes with the following error:''The Abaqus Analysis is terminated because the time increment is smaller than minimum...
05 June 2015 1,532 2 View
Hi guys i m searching for the 3D CAD file of blades: i need to import them in Abaqus. I found some but the program does not mesh them property (bad geometry). I hope you can help thanks in advance
04 May 2015 4,705 11 View
I have the following solid to mesh in order to use it in abaqus and made cosimulation. The domain of the solid is a domain of a parallelepipet less the domain of jacket's structure and it' s a...
04 May 2015 468 1 View
I'm using Abaqus to make a co-simulation s and Fluent to mesh the fluid domain (because it is too complex to do in Abaqus). Now I have some problems to export the mesh from Fluent into Abaqus...
04 May 2015 6,230 0 View
Hi there my project is an offshore wind turbine and I need to simulate a wave, how can i deal with that in abaqus cfd?
04 May 2015 9,587 0 View
It's not fair the conceptual framework between xtreg y on x1 x2 where X2 is independent variable or xtreg y on x1 and control for x2. how can I deal with control variable in Stata? thanks
04 May 2015 6,655 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View