I have done cfd analysis on my robot with 400 iterations in fluent flow and everything went well. Although in the result part the animation is not slowing down even if I increase frame rate. I am using ansys workbench 18.1.
Actually we found various fishes with typical body shape too.
11 June 2024 8,519 1 View
Osmoregulation balance the body fluid of the fish body.
01 June 2024 6,385 3 View
Hi, I am looking to perform an analysis of Br/ KBr in samples of water sources to see if the levels are safe. Due to budget and resource limitation at the stage, I would prefer a method that...
22 May 2024 1,238 5 View
Why do most modern researchers partly or entirely depend on using AL tools for writing or reviewing research articles?
21 May 2024 7,256 1 View
Please ask if you need additional information.
05 May 2024 8,580 2 View
"I am currently working on a narrative review article for my publication as an under grad about oncogenes and their expression. I have written up to 7,000 words so far, but I am not even halfway...
27 April 2024 5,562 3 View
why electron and hole thermal velocities are same for all materials in scaps simulation, why
27 April 2024 2,906 1 View
We know pH range in water body is 0 to 14. 7 is neutral pH.
27 April 2024 4,594 2 View
Deacetylation of chitin results in different de acetyl chitin (chitosan)with various degrees of de acetylation.Such variation produces a mixture of different( chitosans) which is not studied...
02 April 2024 2,739 0 View
I have deposited iron titanate thin films by electrodeposition at different molar concentration. Q #1. In XRD pattern of as deposited I don't observe any intensity peak while after performing MF...
15 March 2024 5,534 12 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...
25 June 2024 4,286 4 View
I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.
24 June 2024 5,125 0 View
I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.
20 June 2024 1,668 0 View
Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...
14 June 2024 6,480 0 View