QTL, recombination frection?

22 February 2021 2,588 2 View

What are the dimensions by which the independent variable (big data) can be measured, Knowing We using the questionnaire instrument?

We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...

21 February 2021 8,133 2 View

How can we determine the band gap of a composite material that is made up of a composition of direct and indirect band gap semiconductor materials?

I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...

17 February 2021 8,104 4 View

What Electrolyte Solution should be used for EIS and CV, While material I'm using is Carbon doped Titania as a counter electrode in DSSC?

Hope so, you are all fine, I want to perform EIS and CV of my material Carbon doped Titania as a counter electrode for DSSC, I just want to know what electrolyte solution and in what molar...

25 December 2020 7,095 3 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

What are the free fee journal in Scopus or Clarivate classification deal with geotechnic ?

I want to introduce my manuscript to journal which is not take fee on publishing.

15 November 2020 609 3 View

Why the crystallographic plane (100) has higher growth rate than other planes such as (220), (111) in (100) oriented crystal?

Dear All, Here I have an interesting question that comes to me about crystallographic planes and growth rate. The literature survey shows, the (100)-oriented crystals the crystallographic plane...

06 November 2020 9,490 10 View

Can we co-relate that A-site vacancies are one of the main reasons for (110)-texture formation? But how?

A-site deficient 0.1BiScO3-BaTiO3 (BSBT) thin films were deposited on Pt/TiO2/SiO2/Si substrate by using PLD. XPS results revealed that A-site vacancies increase with the increase of deposition...

05 November 2020 9,281 1 View

Difference between Data-Driven Adaptive Robust Optimization and Adaptive Robust Optimization?

Could you make some points about the difference between Data-Driven Adaptive Robust Optimization and (classic) Adaptive Robust Optimization?

01 November 2020 9,653 3 View

Can anyone tell me that how to find dangling bond in GaN, AlN or AlGaN?

I want to know about the dangling bond? by which method we can find it, does its need some special type of characterization just like XRD etc... or method i want to find dangling bond effect in...

26 October 2020 1,938 6 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

I am interested in medicinal chemistry field, which books are highly recommended to learn from?

I am at the beginner level in drug design and drug discovery, and I am interested to learn more about this field. Which books are highly recommended to start from and gives me all essential...

02 March 2021 8,437 2 View