09 March 2020 4 4K Report

I am simulating a sheet metal forming process (Deformable Vs Deformable). Incorporating anisotropic elastic properties would need 21 constants. To make simulation easier, can isotropic elastic constants be used with Hill's yield criteria and kinematic hardening to mimick anisotropy and cold working?

Note: 3D FEA model

More Tusar Mohanty's questions See All
What is the reason for arising of a negative peak during a sample run in an HPLC system?

What could be the reason behind a negative peak mostly arising during the initial stage of sample run (RT 1-10).

15 February 2021 4,231 4 View

How do I scale up a column for preparative isolation/purification from analytical conditions in HPLC?

What protocol should I follow to determine optimum separation conditions using an analytical column in an HPLC system?

03 February 2021 7,288 3 View

How to calculate the polysaccharide content of a curcuma species through HPLC method?

what all standards are needed to quantify and analyze the composition with a proper method fie for the mobile phase to run the sample ?

31 January 2021 7,704 4 View

How to extract a single stranded DNA from a double stranded DNA sample isolated from stem borer(rice affecting insect) ?

How to extract a single-stranded DNA from a double-stranded DNA sample isolated from stem borer(rice affecting insect)? As I need to amplify ss Dna using a COX-1 marker having primer sequence as...

22 January 2021 3,424 3 View

How can I check the chemical composition of an essential oil using HPLC analysis?

Injected an oil having a concentration of 832mg/ml and found a flat top peak and was not able to quantify. How to resolve this problem?

20 January 2021 8,461 3 View

How to simulate desiccation in molecular dynamics?

I'm trying to study the effects of desiccation on some proteins, could someone tell what solvent or what simulation conditions I should set up to simulate a desiccation environment on GROMACS.

05 January 2021 7,033 3 View

What is diffrence between coupling buffer and immobilization buffer in SPR experiment?

i am performing SPR experiment and i am referring some journal and websites they stated regarding coupling buffer and immobilization buffer so ihave confusion about these buffer.

06 December 2020 470 3 View

What is the scope of doing PhD in Virology in the UK?

With the great interest in Virology in the world due to the COVID-19 pandemic and its related vaccine development is doing a Phd in Virology from a good institute in UK the right thing to do?

26 November 2020 3,681 3 View

Is it a feasible way to model CO2 emissions Mathematically?

I am working on the Environmental and Social indicators. So the easiest way is to get the solution is to go for any LCA tool;But my doubt is ,is it possible to mathematically model the Emissions...

17 November 2020 8,492 3 View

How to fix this gromacs error?

Residue 6 named GLU of a molecule in the input file was mapped to an entry in the topology database, but the atom CG used in that entry is not found in the input file. Perhaps your atom and/or...

16 November 2020 1,110 3 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close