Can I make tris-HCl without Tris base?

More Tahrima Huq's questions See All

How I can know the completeness and contamination level of bacterial genome sequence from assembled FASTA file?

I want to know the completeness and contamination level of bacterial genome sequence. I have the assembled FASTA file of the bacterial genome sequence. Are there any online tools where I can...

12 May 2024 9,922 2 View

What Machine Learning approach for climate change impact assessment?

What machine learning model use for climate change impact evaluation? Have any ML or AI technique use in climate change vulnerability monitoring?

01 August 2023 490 0 View

How to prepare 3M potassium chloride solution?

how to prepare 3M potassium chloride solution?

11 March 2023 3,948 0 View

What is the impact of MOSFET body-effect on the oxide and depletion capacitances?

Positive Vsb increases the depletion width near the channel region which eventually increase the threshold voltage. What effect does this have on the two capacitances Cox and Cdep?

09 April 2022 5,353 6 View

What are the terminals 'e' and 't' in BSIM-CMG 110.0 model?

BSIM-CMG model has only one gate terminal as for any mode, the gates are common. In the verilog code there are 5 inout terminals: g, s, d, e, t. Is 'e' the body terminal for Bulk mode? If yes,...

13 September 2020 1,613 1 View

How to simulate the veriloga based Stanford CNTFET model in Cadence?

I am trying to simulate following the instructions in the pdf attached. But I keep getting the following error: "Missing or corrupt .oa file in cellview 'cnt/nCNT/spectre cmos_sch cmos.sch...

11 March 2020 9,787 4 View

Should I present a poster paper or try again for full paper?

A research paper of mine has been accepted at an IEEE conference. Although I submitted my best work as a research paper, my best was not good enough and the reviewers threw it with the poster...

12 November 2018 2,374 4 View

I want to work on Basel III implementation based on capital regulation and risk-taking. Can anyone suggest me a suitable title for this work?

In this title I'm going to use NSFR, LCR and Ownership variable as major variables.

07 July 2018 2,659 3 View

Does anyone know, if it is possible to make Conductive Indium Paint? If so, can someone give me some suggestions, papers etc?

I have been trying to use different conductive paint to attach electrode to a semiconductor bar. I am also trying to match the work function of the semiconductor to the filler in the conductive...

01 April 2018 3,012 3 View

Can you suggest a suitable title based on the given information?

Dear Researchers, I'm going to revisit the nexus of ownership influence on regulatory pressure, risk and performance in an emerging economy. Where in a simultaneous equation approach capital, risk...

10 February 2018 4,119 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

How to check pH of a high strength hydrogel?

We are working on biopolymeric hydrogels. Our system is highly viscous and sticky, and the gel formed are high in strength. We are unable to use pH electrode and pH strip. Please suggest an easy...

30 July 2024 942 2 View

EDTA buffer solution?

Hello everyone! How can i prepare EDTA buffer solution (pH 8.2) to determine GSH levels? Thank you in advance.

29 July 2024 4,374 1 View

Whether i can preserve leaves samples in 2.5% glutaraldehyde in 0.05 M phosphate buffer, pH 7 for coming several weeks for further LM study ?

I want to preserve the sample leaves for the LM study of the stomata and conidia analysis. Whether 2.5% glutaraldehyde in 0.05 M phosphate buffer with pH 7 can be applied for preservation.

29 July 2024 8,560 0 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How can I regenerate a SCX column modified with Sulfonate group (Thermo 054995)? The colmun has lost its Resolution and peak to valley ratio?

The column is used in Ion Exchange Chromatography of Monoclonal antibodies and the method of analysis is based on pH gradint.

13 July 2024 7,462 1 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View