What binders suggestion that I can use for zinc alloy?

More Zatul Faqihah Salaha's questions See All

What method should i use for mediating variable?

I'm still learning and confuse, which method should i use for my study. What is the method should i use if 3IVs, 1mediate and 1dv. Some say mediate analysis, some say Smart PLS SEM more easier bcs...

09 January 2024 8,626 2 View

How to determine ball milling duration for metal materials?

I am conducting research on combining several powdered materials through ball milling, and I'm seeking guidance on how to determine the optimal milling duration based on the material composition....

03 November 2023 6,778 1 View

What does phase mean in alloying metals?

Here are the text from the journal i read: The grain size of the Zn matrix decreased gradually as the content of Fe increased. In the as cast Zn-0.2Mg alloy, there was only a single second phase...

06 August 2023 8,629 4 View

What are the differences between potentiodynamic polarization testing and electrochemical impedance spectroscopy for corrosion testing?

Based on my readings, it appears that researchers commonly utilize Electrochemical Impedance Spectroscopy (EIS) as a method and present the results using Potentiodynamic Polarization Curves. To...

06 July 2023 7,059 2 View

Is cytotoxicity testing alone sufficient to determine the suitability of a material for in vivo implantation?

Given the completion of mechanical testing (e.g., compression, pull-out, etc.), this inquiry questions whether a cytotoxicity test using the MTT assay alone is adequate for assessing material...

30 May 2023 3,009 2 View

How endonuklease restriction enzyme indentify mutation in gene?

about mutation

20 May 2023 3,237 2 View

How to determine the appropriate optimization method for coating: Taguchi method vs full factorial design?

What are the factors to consider when deciding between the Taguchi method and full factorial design as an optimization method for coating processes?

25 April 2023 844 3 View

How to define corrosion current density in simple terms?

In the article I read, in the results part. There are graphs of corrosion current density (Icorr) of different samples that has been immersed in SBF solutions.

12 March 2023 7,085 11 View

Is there any way to calculate the amount of CO2 released from an area based on the information of increased C02 concentration (PPM) for a year?

In case of whole world we can calculate that how much CO2 are released (net released) based on the information of increased CO2 concentration. Using 5.137 x 10^18 kg as the mass of the atmosphere...

26 June 2019 4,265 6 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,561 0 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 724 3 View

How select composition for ods-high entropy alloys?

31 July 2024 2,794 1 View

Why Powder XRD is performed after cruhsing a crystal if Single Crystal XRD analysis of the same crystal has been performed already ?

What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?

30 July 2024 6,259 4 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,924 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,507 0 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,937 1 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,488 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,210 5 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,492 3 View

Syed Abbas Raza

Are you utilizing uniaxial pressing or Cold Isostatic Pressing? What is the maximum pressure you have applied?

Any organic binder is suitable like Polyvinyl Alcohol or Poly Ehylene Glycol is suitable for this case. Please control the amount used to avoid slurry formation. Since the density of Zinc alloys is around 6 gm/cm^3, use 1 ml for 2 mol gm of your alloy powder and add more if need be.

Good Luck!!!

Zatul Faqihah Salaha

Syed Abbas Raza Im using uniaxial pressing with max 500 MPa. Thankyou for the tips and info! This is very helpfulll