How to visualize stress in a coating defined by "Skin" in Abaqus?

Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...

16 February 2021 1,594 3 View

Is a Strong correlation between the Moderator variable and the dependent variable an issue for moderation model (model 1) in Hayes PROCESS?

In a typical moderation model with one moderator, is it a problem if the moderator and the dependent variable show a strong correlation (say 0.85)? What if a strong correlation exists between the...

27 January 2021 4,937 4 View

Which syringe filters (e.g., PTFE, MCE, PVDF, CA, PES, etc.) are the best to filter TBS/PBS buffer (pH 7.5-8.5) and glycine buffer (pH 2-3) solutions?

I intend to purify antibodies from serum using the affinity procedure, and I need to filter the binding (TBS/PBS) and elution (Glycine) buffers before applying them to my solution.

06 January 2021 5,769 3 View

Gear reduction for back-drivability of a motor?

Hi everyone, Does anyone know up to what reduction ratio of gear does a motor remain back-drivable? I want my robot to have safe interactions with the environment and other humans. Can you give a...

26 December 2020 7,142 3 View

How to export DigSilent Plots with high quality?

Hi all; I've started using DigSilent these days. However, I'm wondering how can I export the results with high quality the same as MATLAB plots as I currently do. Thanks

19 December 2020 2,666 2 View

How to assign initial stress to a coating in Abaqus?

Hello! I am trying to define/assign initial stress to a coating I modeled on a substrate. I defined the coating using "skin" function. I have tried "predefine filed" in load section. But it only...

10 December 2020 2,921 8 View

How to model a multilayer coating in ABAQUS?

Hello! I'm trying to model a multi-layer coating on a substrate in abaqus. The layers are homogenous and isotropic. My question is how should I approach the modeling? WHAT I'VE TRIED SO FAR: I...

09 December 2020 1,235 3 View

How can I calculate Nusselt number by using this equation (Nu = ht.gradTx * nx + ht.gradTy * ny + ht.gradTz * nz) step by step in COMSOL?

Calculate the Nusselt number using the COMSOL Program

09 December 2020 3,354 3 View

How to calculate sulfur loading of lithium -sulfur batteries using Li2S8 catholyte?

I am gonna use Li2S8 catholyte to introduce active material to cathode instead of using sulfur. May anybody kindly guide me about the way I can calculate the amount of sulfur (g/cm2) loaded on the...

07 December 2020 7,556 2 View

How to great data visualization and what example for it ?

i need explain data visualization and what type it and how great it by excel or other program > paper attached for help

30 November 2020 1,159 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

No title

02 March 2021 3,060 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View