How to visualize stress in a coating defined by "Skin" in Abaqus?

Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...

16 February 2021 1,594 3 View

Is a Strong correlation between the Moderator variable and the dependent variable an issue for moderation model (model 1) in Hayes PROCESS?

In a typical moderation model with one moderator, is it a problem if the moderator and the dependent variable show a strong correlation (say 0.85)? What if a strong correlation exists between the...

27 January 2021 4,937 4 View

Which syringe filters (e.g., PTFE, MCE, PVDF, CA, PES, etc.) are the best to filter TBS/PBS buffer (pH 7.5-8.5) and glycine buffer (pH 2-3) solutions?

I intend to purify antibodies from serum using the affinity procedure, and I need to filter the binding (TBS/PBS) and elution (Glycine) buffers before applying them to my solution.

06 January 2021 5,769 3 View

Gear reduction for back-drivability of a motor?

Hi everyone, Does anyone know up to what reduction ratio of gear does a motor remain back-drivable? I want my robot to have safe interactions with the environment and other humans. Can you give a...

26 December 2020 7,142 3 View

How to export DigSilent Plots with high quality?

Hi all; I've started using DigSilent these days. However, I'm wondering how can I export the results with high quality the same as MATLAB plots as I currently do. Thanks

19 December 2020 2,666 2 View

How to assign initial stress to a coating in Abaqus?

Hello! I am trying to define/assign initial stress to a coating I modeled on a substrate. I defined the coating using "skin" function. I have tried "predefine filed" in load section. But it only...

10 December 2020 2,921 8 View

How to model a multilayer coating in ABAQUS?

Hello! I'm trying to model a multi-layer coating on a substrate in abaqus. The layers are homogenous and isotropic. My question is how should I approach the modeling? WHAT I'VE TRIED SO FAR: I...

09 December 2020 1,235 3 View

How can I calculate Nusselt number by using this equation (Nu = ht.gradTx * nx + ht.gradTy * ny + ht.gradTz * nz) step by step in COMSOL?

Calculate the Nusselt number using the COMSOL Program

09 December 2020 3,354 3 View

How to calculate sulfur loading of lithium -sulfur batteries using Li2S8 catholyte?

I am gonna use Li2S8 catholyte to introduce active material to cathode instead of using sulfur. May anybody kindly guide me about the way I can calculate the amount of sulfur (g/cm2) loaded on the...

07 December 2020 7,556 2 View

How to great data visualization and what example for it ?

i need explain data visualization and what type it and how great it by excel or other program > paper attached for help

30 November 2020 1,159 2 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

How do I connect DAB DC DC Converter to a battery in matlab simulation ?

I am trying to model a DAB converter and I need to observe the power transfeered to the load side on varying the phase shift between two bridges, hence I couldnt take a constant load e.g...

09 February 2021 6,489 3 View

Is there a generalized method to derive current-mode model of any DC-DC converters?

Hi all, As new DC-DC converters are being proposed, associated control method should be proposed and based on the small-model signal analysis of the DC-DC converters. Using average space state...

06 January 2021 7,247 3 View

Why mutual inductor takes high current at no load condition?

I simulate an inductive wireless power transfer system in matlab. I set the primary and secondary mutual inductor resistance is 0.3ohm. So when i run the circuit it took high current at no load...

29 December 2020 9,536 3 View

How do I calculate the torque required for linear motion?

23 December 2020 5,064 3 View

Simscape Linearization Error | frestimate(modelname,op,io,in) ?

Hello ! When tried to linearize the model for Bode plot in matlab getting the following error. In "frestimate(modelname,op,io,in)", it is required for each of the linearization input I/O...

08 December 2020 4,598 1 View

What kind of possible device mismatch we can expect while designing circuits with Current Mode Analog Building Blocks?How these mismatches affect THD?

Large values of resistors and capacitors are hard to match in the fabrication phase. It will create some systematic mismatches. So how to avoid those kinds of mismatches in case of current-mode...

19 November 2020 3,709 8 View

Can Copper be sputtered (via PVD) onto Platinum-Iridium to improve solderability?

Hi! First time poster on RG! I would like to solder (ball grid array reflow) onto a Platinum/Iridium alloy without the use of special Platinum soldering fluxes. Can copper be sputtered onto...

18 November 2020 2,105 3 View