Can I design Young's Double slit experiment on COMSOL using RF module ?

01 December 2018 1 5K Report

I want to design and simulate Young's double slit experiment on COMSOL using RF module ? I am unable to get results. Can anyone please help me ?

Abbas Majidi Bidgoli

You can watch many tutorial videos on YouTube, below link can help you. you can follow it and change it's geometry and boundary conditions to obtain desired configuration. be careful about the rest, they must be unchanged.

https://www.youtube.com/watch?v=gkWjA8yN-X8&index=9&list=PL7E9074B722FB855C

Badges
Science topic

More Tanasam Shaheen's questions See All

What is the average stove efficiency for household gas stove especially in the Indian subcontinent?

In one paper, I saw it to be about 36%. But as the paper was published in 1997, shouldn't modern household gas stoves be more efficient?

14 December 2020 6,199 6 View

Is there a guide for Aspen Hysys to show unit operation calculations?

For example, let's say if I design a conversion reactor and give inlet temperature,pressure,composition and reaction kinetics then Hysys will show me the outlet conditions. It doesn't,however,show...

09 December 2020 8,375 3 View

Which decision rule algorithm is best in machine learning? Is there any algorithm based on rough sets that gives good results?

I am trying to learn some algorithms that extract decision rules from data sets, particularly by using rough sets. I need to know whether they are reliable and efficient (like LEM2) for real datasets?

17 August 2020 7,013 6 View

Does surface particle size (surface component) has any relation with atmospheric optical depth (atmospheric component)?

I have estimated thermal inertia for a surface followed by its particle size, I have to look for the relation between particle size and atmospheric optical depth, I have gone through the...

11 October 2019 7,986 3 View

Techniques which can be used for delineating the rim of a feature?

Hi, I want to delineate the rim of this crater (refer attached image) using remote sensing software, apart from visual interpretation what are the other available techniques which i can opt...

06 September 2019 9,987 3 View

Is there any data set from where i can find country wise data on FDI & portfolio investment inflows in Pakistan?

i need data on private capital inflows in Pakistan, for this sake i have to generate the variable by adding FDI in the reporting economy and the private elements of portfolio investment, financial...

07 July 2019 4,316 5 View

Extracting maximum elevation points between 0.8R and 1.2R?

I have xy location and radius, from these details i make buffer of 0.8R and 1.2R, then i have divided the circles into 36 segments with an interval of 10 degree. I have DEM image of this region....

08 May 2019 4,892 2 View

How can we justify that it is the interference pattern of electromagnetic waves?

I designed double slit experiment using RF module in COMSOL and tried to get interference patter, The results are following with 930MHz frequency. What do you predict from the pattern?

21 January 2019 8,356 2 View

Including Renewable Energy Sources in Matpower to solve Optimal Power Flow?

I'm modelling my own grid in matpower to calculate the optimal power flow (opf). The thing is my grid has WT, PV & batteries in them along with the conventional generators. Does anyone know...

29 December 2018 4,379 6 View

How to get Mars true solar local time ?

Hi, I have all these information (given below) except for Mars true solar local time, Is it possible to calculate the true solar local time from these information ? Earth date - 28/10/2014 UTC-...

31 October 2018 4,065 2 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View