How to publish M.A. Dissertation in CARE Listed Journal?

Do i need to summarize my M.A. Dissertation in short as an article/research paper (3000-5000 Words) Do i have to paraphrase all my work and reproduce it Do i need to give my own reference? and...

30 November 2019 1,917 3 View

What statistical tools should i use for the given objectives?

Proposed Title of my PhD is "A Critical Study of Health Schemes Implemented by Government of Maharashtra with Special Reference to Janani Suraksha Yojana (JSY), Janani Shishu Suraksha Karyakaram...

21 October 2019 9,624 4 View

Effective protocol for carboxymethyl cellulose resin preparation (with its sodium salt) for IEX?

Unable to find a suitable protocol for preparing CMC for IEX

03 January 2019 5,508 1 View

How to get the response of a Viscoelastic material modelled in Abaqus at a particular temperature ?

Hello All, I have modelled asphalt in Abaqus using the linear viscoelastic theory in abaqus considering the shear relaxation modulus, the WLF factors and the reference temperature equal to 21...

15 June 2018 3,490 3 View

How can be initial conditions of displacement, velocity and acceleration provided in abaqus?

Hello, everyone! I'm trying to do dynamic analysis in abaqus. I want to provide initial conditions of displacement, velocity and acceleration for all nodes and all degrees of freedom, but I can't...

29 May 2018 7,421 11 View

How can i predict future Land use Land cover changes using GIS?

How can i predict future Land use Land cover changes using GIS?

27 February 2018 9,069 16 View

How to calculate average length in an image with a wide distribution of rod like structures?

I have images with numerous rod like structures and I need to calculate the average length of the rods. I am trying ImageJ to measure them manually but the data set is huge. Any suggestions?

23 May 2014 361 5 View

Does the relation between tensile strength(TS) and shear strength(SS) of 0.50 via von Mises and 0.577 vis Tresca criterion hold for metallic glasses?

Are these ratios experimentally validated good first approximations for the relationship between TS and SS for metallic glasses?

12 April 2014 7,131 4 View

Typically, how do hysterisis and eddy current losses in AC induction motors compare with copper/winding losses?

I am using FEMM to see how the losses in a motor change when different soft magnetic materials are used for the stator/rotor laminations. My simulation showed that the no-load losses (hysteresis,...

16 March 2014 1,927 3 View

How can I prevent a copper thin film from de-wetting from my substrate at high temperatures?

In my experiments, I am directly pyrolyzing photoresist (PR) in an inert or reducing gas to form a C film. I have deposited Cu via thermal evaporation (50 or 300 nm), before spin-coating the PR in...

27 February 2014 7,701 6 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

How to increase solubility of Poly acrylic acid in Dioxane solvent?

I am working with Polyacrylic acid (100.000Da) and instead of water, I need to use another solvent (dioxane) to dissolve PAA. However, because of the high molecular weight, it's quite hard to...

25 February 2021 2,225 5 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

What is the system of units used in the thermal conductivity by Spitzer and Harm?

23 February 2021 9,253 1 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View