the details are not available in the Addgene website.
Hi, Parotosh,
thank you for the suggestion. I tried to use nTI and DNAstar, but could not figure it out. I am not aware of using bioinformatic softwares. I will try once more and get back to you.
Hi all. I deal with flow cytometry data and analyze by FlowJo. In order to analyze and represent it in a better way, I would like to buy the Origin lab software (https://www.originlab.com/) which...
11 December 2018 7,475 4 View
Flow cytometry data which can be presented in various ways like dot plots, contour, density plots, etc. But in all these representations, the depth of a given population is not very clear in 2D...
10 November 2018 7,543 3 View
Flow cytometry analysis has become a routine in now-a-days research. It is more important in hematopoiesis studies where a desired cell type, identified by a single marker or combination of...
09 October 2018 936 5 View
Hi everyone! I am trying to raise an antibody specific to a protein, which is highly similar and shorter in length compared to a different protein from the same family. As it makes clear I do not...
08 September 2016 2,269 6 View
I want to show the data points about the test and control samples in a vertical dot plot/scatter plot using Excel 2016. Have tried in various ways to figure it out, but could not. Can anyone...
07 August 2016 1,585 8 View
I am doing a multi-color flowcytometry analysis of mouse bone marrow cells, for which I use a kit. Each time, I need only 0.3-0.6 ul of certain antibodies. This has a chance of increasing errors...
06 July 2016 1,285 4 View
I ve spotted a few colonies growing on Yeast extract, Peptone and dextrose (YPD) agar medium, which is exposed to a fumigated room for 3.5 hours and incubated at 30 degrees centigrade for 41...
05 June 2015 2,745 1 View
During analysis of cell suspensions expected to harbor a particular population of low number, how this 10^4 (10000) events cut-off can be managed? Starting the analysis with high number of cells...
03 April 2015 1,947 4 View
Is there any review about hematopoieitic differentiation of mouse embryonic stem cells on OP9 cells with complete profile of markers expressed? I have tried in all possible ways to find the...
03 April 2015 4,983 8 View
By 2nd day of culturing HEK293 and mESCs, a lot of precipitates are found in the dish and affect the cell health badly (worse in the case of mESCs). By 4th or 5th day of culture all the cells are...
11 December 2014 4,519 3 View
I'm cloning a fragment of 3200 nts into plasmid. The cloning was successful, however, 02 amino acids were mutated. Now I want to fix these 02 aa by site-directed mutagenesis technique using...
08 August 2024 4,645 2 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View
Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...
06 August 2024 641 2 View
Hi all, I need to introduce an ARS (autonomously replicating sequence) in my plasmid but I'm not sure which position would be the best. Does anyone have any suggestion? A picture of the plasmid...
05 August 2024 1,573 4 View
I want to introduce a point mutation (change in one nucleotide) into my gene of interest (DNA binding domain) I have designed primers as recommended on the Data sheet of the kit : -Both primers...
05 August 2024 9,059 3 View
I am performing ligation of the plasmid and a target gene. The steps I have taken are: 1. Double digestion of the plasmid and target gene 2. Ligation of the plasmid with the target gene 3....
05 August 2024 2,570 3 View
I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...
04 August 2024 9,913 7 View
Dear All, I am trying to transfect a pCDNA3.1 vector containing my gene of interest. The purpose is to figure out the localization of the protein of interest. I have fused the protein with GFP on...
31 July 2024 9,892 4 View
I am currently investigating the cytotoxicity of a series of herbal extracts, and like many studies, I have been using the MTT assay to evaluate cell viability. However, I am encountering a...
31 July 2024 193 4 View
Hello I am trying to create a stable cell line in HEK293 via Lipofectamine 3000 transfection. My plasmid is a CD63-IL10-GFP construct with Puromycin resistance. I am successful with the...
30 July 2024 6,648 1 View