What do we mean by the hardness of nanoparticles?

Dear Researchers & Professors, Please let me know the answers for the following queries. 1. What do we mean by the hardness of a nanoparticle? 2. If the hardness of Al2O3 nanoparticle is...

04 May 2019 7,390 4 View

What could be the Cp of CNT and Aluminium Nitride nanoparticles?

Please let me know the Cp value of CNT and Aluminium nitride nanoparticles.

04 May 2019 6,804 4 View

DISCUSSION CLOSED - on thesis evaluation?

The discussion is closed as per the valuable suggestion of Professor Pawan Kumar Khanna. I thank him for enlightening me.

03 April 2019 2,533 3 View

How to determine the particle size from DLS ASCII sheet?

I have been provided with a data sheet with Intensity % and particle size in nm. Can anyone help me out to to figure the ways by which I could calculate the average particle size from it? I need...

02 March 2018 1,917 7 View

Can anyone suggest the best way to prepare SWCNT in water based nanofluid?

02 March 2016 7,943 4 View

Can anyone suggest Surfactants/Dispersants for MgO and CuO in DI water as nanofluids?

Dear Researchers and Professors, I dispersed 0.5 gms of MgO in a litre of DI water and sonicated it for 3 hours and found that, it did not disperse well. After keeping it idle for a day, found...

02 March 2016 145 3 View

Can someone please send me full papers on the fluid flow through ducts?

Can some one provide me with full research papers on flow of conventional fluid and Nanofluid through ducts? Any number of papers as much possible.

08 September 2015 8,100 0 View

Can anyone kindly guide on the preparation of nanofluids for Forced Convection Test Loop?

Please suggest each basic step to prepare a nanofluid for Forced Convection Test Loop setup. How much quantity of nanofluid is needed for the test loop? How much nanoparticle is to be taken to...

06 July 2015 1,480 2 View

What are all the possible thermal and electrical properties to be measured after synthesizing a nanoparticle and when using it as nanofluids?

I wish to know whether a synthesized nanoparticle can be used as effective nanofluid for thermal and electrical application. Also I am in need of the measurement techniques available and can be...

06 July 2015 6,397 8 View

Plagiarism Software

Dear Professors & Researchers, Can anyone kindly provide me with a list of good plagiarism check software, which would be affordable for me to buy and install in my personal...

01 January 1970 6,567 8 View

What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View

How to model static fluids in ANSYS?

Hi I was wondering if there is a way of simulating static fluids (including brownian motion) of nanofluids in ANSYS. I am currently working on a theroretical based project where I am trying to...

20 February 2021 776 1 View

Are ZnS nanoparticles moisture sensitive?

Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...

17 February 2021 1,709 3 View

How does a freeze dryer destruct your solid sample?

Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...

15 February 2021 6,749 2 View