Can anyone help with a problem regarding developing welded and bolted connections in abaqus?

30 April 2015 1 441 Report

we are developing a model of box shaped steel frame on abaqus by using ISMB-600. we are also using stiffeners to prevent web buckling so while developing model we were finding some issue on making welded and bolted connection. we are attaching an image of our model.

Prabuddha Sathurusinghe

You have to add constraints. Refer to Abaqus documentation vol 5 Part VIII: Constraints.

Badges
Science topic

More Chintan Pathak's questions See All

How can we count the number of edges in an edge detected image using canny/sobel algorithm in MATLAB?

I need to process an image for edge detection and then want to count the number of edges in that image.

29 December 2020 5,594 2 View

Why the journal "the lancet" is only indexed in scopus?

I went through "The Lancet" journal website and saw the immense impact factor of 60.392. Then to my surprise I found that the journal is only indexed in scopus. Such Imapct factor journal is...

21 December 2020 152 3 View

Which factor controls Peak intensity in Rietveld refinement?

I am refining structural parameters of my sample. after inserting all parameters in sequence, When I take first Run in refinement, the intensities of all peaks diminishes to zero of calculated...

07 October 2020 8,598 1 View

What would be the effect of size of the nanoparticles on the birefringence of nematic liquid crystalline materials?

Usually, birefringence of nematic liquid crystals (NLCs) can be tuned by doping of nanoparticles into it. But what will happen if we dope the same nanoparticle of different sizes? Will...

20 September 2020 3,693 3 View

Which is better for thin film growth, electron beam evaporation or sputtering?

which is better for thin film growth, electron beam evaporation or sputtering? which results in better film quality?

24 July 2020 6,275 4 View

What minimum operating voltage for CMOS technology and magnetic field required for spintronics technology?

Generally, we always try to give low input to operate a device. What are the minimum values of voltage for CMOS technology and magnetic field for spintronics technology?

24 July 2020 5,610 2 View

Where do I find consumer mobile datasets that include his or her social media activity and his smart home dataset?

I am looking for a data set to find out the loyal consumers.

26 June 2020 2,973 1 View

Which technology should we need to apply to get the present condition of soil and suggest us some crops from a remote place?

At present we are updating our work. So I need your suggestions. https://www.researchgate.net/publication/335800982_IoT_based_Smart_System_to_Support_Agricultural_Parameters_A_Case_Study

20 June 2020 3,748 11 View

How to plot data in 10X10 matrix in which all the diagonal elements are 0 and the matrix is symmetric about the diagonal?

I have a data of comparison of 10 proteins with each other under two parameters i.e 100 entries in the shells of two 10X10 matrix in excell sheet. I want to see whether both of these data sets...

02 March 2020 1,593 5 View

What are the effects of using powerful magnets around AC current?

I am trying to connect two sockets( sockets being flat surfaces on both sides) using powerful (small sized ~8mm diameter) neodymium magnets with 3 or 4 on each side of the socket so that the pull...

03 January 2020 8,835 3 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

I have designed reflectarray element and feeding it though Horn Antenna on HFSS. After full wave simulation, I am not getting desired results?

I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...

01 March 2021 9,701 5 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View