Can anyone help to solve this error in fluent, " Could not handle event: SolutionStatusUpdate"?

More Raid Mahmood's questions See All

Can I use the CFD FLUENT approach to investigate and examine the Reynolds number (Re) and Froude number (Fr) of the two-phase flow ?

By applying the Buckingham Pi theorem, dimensionless parameters such as Reynolds number (Re) and Froude number (Fr) can be indicated for the two-phase flow. Can I use the CFD FLUENT approach to...

09 October 2014 287 10 View

Grid independent study is important in FLUENT for certain geometry,If I change geometries can I keep the same B.C in use?

Grid independent study is important in FLUENT for a certain geometry to get right answer, but is it necessary to do another grid independent study if we want to change the geometry and keep the...

09 October 2014 4,242 14 View

Is there any effect of surface tension on the two-phase flow behaviour at adiabatic flow?

Adiabatic two-phase flow (gas-liquid) in horizontal pipe.

03 April 2014 8,692 4 View

How can I solve the " divergence detected in AMG solver:vof1 " problem in 3D multiphase simulation?

I am using 3d cylindrical pipe, steady state, segregated solver for simulation immiscible flow in a pipe. I am getting this error " divergence detected in AMG solver:vof1 " I tried with all...

08 September 2013 5,158 4 View

Can I use 2D geometry to simulate a two phase flow (gas-liquid) inside a horizontal pipe to predict the flow pattern by using CFD Fluent code?

Working fluid for the two phase flow is (steam - water) as (gas - liquid).

08 September 2013 598 4 View

How can I predict the dryness fraction or vapour quality (X) in two phase flow at the pipe outlet by using FLUENT?

I am facing this issue because I have no Idea about the area that occupied by gas or liquid at the pipe outlet. Any help for that?

08 September 2013 765 19 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

José Julio Ferraz de Campos Jr.

Hello

see if it helps you:

http://www.cfd-online.com/Forums/fluent/87264-fluent-supersonic-flows-strong-shock-waves.html

Raid Mahmood

Thanks for that Julio but my case is not supersonic. The case that I want to simulate is subsonic incompressible two-phase flow. The intention is to predict the flow behaviour and patterns.