05 May 2016 1 5K Report

I want to understand the exact procedure to be used for calculating carbon foor prints of steel rolling industry. 

More Janak Valaki (PhD)'s questions See All
Which vegetable plant seed has the highest oil yield?

I am looking for a guidelines on the vegetable plant which bears highest oil yield.

08 September 2019 1,392 4 View

How to calculate life cycle impact for a manufactured product?

I have not come across any paper where it is systematically stated about how to calculate life cycle impact of a product manufactured using any process. if any one has idea or paper, kindly let me...

07 August 2016 1,454 5 View

What are the direct and indirect benefits of pursuing a PhD program?

During our formal conversations, many of my colleagues and friends used to tell me what are the direct benefits of pursuing and having a PhD degree? i could figure out some of them. But i thought...

06 July 2016 7,815 3 View

Which are the criterions for safe disposal of waste water from vegetable dehydration industry?

are there any criterions laid down by government of india or by any regulatory body worldwide for te safe disposal of waste water from vegetable dehydration industry? which are he technologies...

06 July 2016 9,376 8 View

What are the industrial means to recover the water from mist air?

are there any technology available to recover the water from the mist air or evaporated water mixed air?

05 June 2016 9,934 1 View

Are engineering students really interested in engineering? Is engieering education following BA , BCOM and Bsc route of downfall?

It has been observed that students are interested in matters other than studying engineering. they are preparing for either GATE, GRE. TOFEL, GCET, CAT, UPSC or state level competivie exams.

04 May 2016 2,911 0 View

Are technical books loosing its charm ground as reference books amongst engineering students?

Students have turned to refer local publishers books as test books.

04 May 2016 5,770 1 View

How to prevent thickening of the vegetable oil as transformer oil under working conditions?

are there any process to be applied on the oils? or if at all we can't prevent it, then what are the methods available to remove the thickened mass from the remaining oil and reuse the left over oil?

01 February 2016 7,288 1 View

Similar questions and discussions
What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close