Dear all, Can any one say how to calculate convective mass transfer coefficient and evaporative heat transfer coefficient in fluent?

Is it possible to find in fluent? Any other method is there?

10 September 2020 5,492 3 View

Is it correct to take an average of HRV recorded for 30 minutes for comparing two groups?

I have collected a 30-minute HRV during a stressful task for two different groups. To compare the variations, i have seen many papers average the hrv over the collected time. Is that a right...

03 October 2019 9,174 1 View

Why charges should induce when Glass rod is rubbed with silk cloth?

Here I mentioned only Glass rod and silk cloth. This can be anything from triboelectric series. But, why should it happen? Why should different charges accumulate in two materials and then...

22 August 2018 2,619 2 View

How do you Evaluate Telomere length through qPCR?

Hello Everyone, I am Venkat and am trying to work with cells and tissues from the aorta. I am hoping to study telomere lengths from my samples and I was wondering if there were a reliable way to...

07 December 2017 8,250 7 View

Two-dimensional approximation of cylindrical bar cropping process - plane stress or plane strain?

19 July 2017 1,236 3 View

Can someone explain the steps for calculating the electron transfer number in oxygen reduction reaction?

When the ORR catalyst i synthesized gives five times greater current density than the commercial Pt/C, then the slope of the KL plot for the catalyst synthesized will be higher because of the...

24 July 2016 1,504 2 View

Is anybody working in the area of method of lines computational method to analyse waveguiding structures?

Computational Electromagnetics

18 January 2016 1,190 5 View

How can I integrate FORGE (Bulk forming results) into ANSYS for structural validation considering pre-stress?

To import mesh with pre-stress values into ANSYS?

26 January 2015 671 3 View

How to integrate Pamstamp (Stamping results) into Ansys for structural validation considering pre-stress?

I would like to carry out structural simulation without defining material property in Ansys (Stamping mesh with pre-stress).

21 August 2014 8,522 1 View

How can I find the Valence Electron Count (VEC) for TiNiSn?

TiNiSn is a Half-Heusler alloy with VEC = 18.

28 May 2014 1,428 2 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View