I am planning to model a brick masonry wall to check its failure mechanism on non-linear time history and provide RC jackets to retrofit this wall in both in-plane and out-of-plane directions.
Hi Sandip,
Similar work has been done in Abaqus focusing on steel reinforcements.
You can get ideas from this report:
http://bookshop.europa.eu/en/steel-solutions-for-seismic-retrofit-and-upgrade-of-existing-constructions-steelretro--pbKINA25894/
Regards,
George
These are the properties i have assigned: MP,MU,4,0.75MAT,4 TB,CZM,4,,,CBDETBDATA,1,0.25,0.018,0.35,0.125,0.0001,1 R,3 REAL,3ET,5,174ET,6,170 R,3,,,-82,,,...
03 April 2015 589 2 View
Can we model without using contact elements, i used ''merge node'' options but it doesn't work. In case using contact 173 and target 170, how can we model the perfect bonding?
02 March 2015 4,135 2 View
This is the result i got every time
02 March 2015 6,951 0 View
I have used CONTACT 173 and TARGET 170 element. The shear bond strength of brick-mortar is 0.005 MPa, coefficient of friction for bed joint is 1.2 and head joint is 0.85. Does it works if i use...
02 March 2015 8,322 4 View
Can we mesh a line non-uniformly, I mean If a line length is 100 mm, can we mesh it with a mesh length as for example 25mm, 20mm, 10mm , 20mm, 25mm ???
01 February 2015 2,614 5 View
I want to apply the loads in a masonry wall to check for the load-deflection curve.
01 February 2015 1,578 5 View
Is there any empirical formula to calculate the Elastic modulus of brick with known value of compressive strength?
31 December 2014 8,647 0 View
I want to assign the properties of brick, mortar and interface in the modelling of an unreinforced masonry wall.
11 December 2014 9,187 2 View
I want to retrofit a URM wall with RC jacket in my research and looking for the design of RC jacket.
10 November 2014 5,179 0 View
I can only find a limited number of solid elements but while reading the options in the ''help'' of ansys, many other elements are available.
10 November 2014 1,711 10 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.
08 August 2024 3,161 0 View