Barrelling effect on composite cylinder

01 January 1970 0 4K Report

Barrelling happens during plastic deformation of solid cylinder. Dead zone will be occur between die and specimen during process.

Badges
Science topic

More Anas Balod's questions See All

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

How to determine the dominant orientation of collagen fibers.?

what is the best method to determine the dominant orientation of collagen fibers? i preformed FFT and shited the frequencies , what should be my next step ?

24 December 2020 3,360 3 View

What is the best Machine learning method to extract collagen bundles features ?

what is the best machine learning method , to segment and extract the length , angle and the size of collagen bundles pictures obtained from the human cornea?

07 December 2020 336 6 View

Where could I find IoT devices location dataset in supply chain environment?

I am doing research in permissioned blockhcain more precisely permissioned blockchain application in some sort of supply chain environment involving IoT devices for which I am looking for IoT...

14 September 2020 5,748 3 View

How does peak broadening in XRD relate to residual stresses in thin films ?

The shift in 2teta angle of XRD peaks is related to stress in the film. But for peak broadening how is it related to stress ? Thanks

09 August 2020 532 6 View

Do all random access procedures and packet transmission in NB-IoT happen during one Nprach_periodicity?

Hi all, I have two questions about random access procedures of NB-IoT In NB-IoT, Nprach-Periodicity is the amount of time between two consecutive random access transmission attempts. Random...

01 May 2020 7,684 5 View

What are the best resources to learn cuda programming?

Friends, I have a lot of C programs that I would like to convert to Cuda for performance enhancement but I am facing a lot of problems doing that. So I have decided to learn more about Cuda as my...

26 April 2020 2,925 4 View

Fail Safe N, Orwin method?

I need to calculate Fail-Safe N of my meta-analysed studies. I am having difficulty in understanding Orwin's method. Can anyone please elaborate with the help of an example?

03 March 2020 7,403 3 View

Usefulness of CMA lite version?

Can I do moderator analysis on the lite version of Comprehensive meta-analysis software (CMA)? Or is it necessary to get the Pro version of it to perform moderator analysis? Quick responses would...

02 March 2020 328 2 View

What is the effect of crystal orientation of powder on sintering process?

Crystal orientation of powder is an important parameter in powder technology, so the movement of powder during process depending on this parameter.

11 February 2020 6,092 1 View

Steps to calculate activation energy by coats & redfern method?

I'm a chemistry student and I'm researching the kinetic degradation of mixed plastic waste. I'm having trouble calculating the activation energy by the coats & Redfern method. The data that...

24 February 2021 974 1 View

Droplet PCR in plastic chips always result an unexpected band, any suggestion of possible contaminations and how to improve?

I am doing droplet based digital PCR inside plastic chips. I can get the correct band, but I also consistently get an unexpected band, slightly shorter. I attached a typical gel image here....

18 February 2021 6,618 2 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

How to measure the hardness for PLA & PHAs polymers?

Hello, I am a bit confused on whether to follow ASTM D785 (Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials) or ASTM D2240 (Standard Test Method for...

21 January 2021 7,487 4 View

Where can I find stress-strain data for steel to define plastic properties in Abaqus?

I am looking for stress-strain data for steel to input for the plastic properties in Abaqus. However I cannot find any literature or experimental data on the matter. If full data is not available...

15 January 2021 9,070 2 View

Hi, could anyone help me knowing which kind of Diamond blade would be better to cut thermoplastic composite?

The blade that could cut ceramics, or the one that could cut plastics and polymers?

06 January 2021 2,713 3 View

Which module is preferred in Ansys software to simulate shrinkages of plastic powder for the Injection Molding (IM) process?

I need to know the effect of shrinkage of plastic powder materials by simulation using Ansys or Simufact software.

21 December 2020 5,693 9 View

Blow extrusion of PLA with the HDPE non rotary die. Is it possible?

Hello, I managed to run a small blown extrusion line, head diameter 70mm / screw 45mm. The machine is to be used for extrusion of sleeves from 200 to 500mm wide. Unfortunately, I have a draw...

13 December 2020 2,824 5 View

Which are the quality parameters considered for injection molded plastic products? And which inspection tools are used for the same ?

Quality parameters and inspection tools may differ from product to product. Please write whichever you know.

10 December 2020 1,478 2 View

Will i need to define ductile damage parameters as well as yield stress vs plastic strain values for performing Fire-tensile test of CFRP/GFRP BARS?

Can someone please help me in this regard ... i have modelled a CFRP/GFRP( elastic and plastic properties together with temperature dependent -mass density, thermal conductivity and specific heat)...

03 December 2020 5,435 3 View