what are the steps to deal with autodyn part to simulate blast load on reinforced concrete barrier in ansys autodyn 18.20 ?
Hello everyone, I'm currently collecting Eimeria parasites for in vitro tests and would like some advice on improving the process. Firstly, can I replace chemical-grade NaCl with table salt for...
23 May 2024 5,191 11 View
Hello, I need to use this ion exchange resin to test the efficacy of the purification step by adding it to a microcon (Blaajberg et al. 2010). This article did not mention the working protocol for...
20 May 2024 8,507 0 View
possible support references
30 April 2024 7,604 1 View
possible support with references and literature
12 April 2024 9,526 4 View
has modern technology benefited humans or caused them harm?
11 April 2024 2,479 3 View
Can I use RIPA buffer to lysis insect cells SF9?
10 April 2024 6,249 2 View
in other words, can we resort to previous studies after going to the field to compare and discuss the research results with the previous study?
30 March 2024 1,756 2 View
in social sciences, which is more important, questions or answers, in your opinion?
17 March 2024 8,627 9 View
or provide previous studies and references.
14 March 2024 3,901 0 View
I tried using oil red O and Sudan black B but I didn't get good results. I used cryostat sections and fixed the tissue into formaldehyde and then sucrose in advance but the tissue field is always...
06 March 2024 6,321 2 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...
27 July 2024 5,748 0 View
Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...
25 July 2024 9,058 4 View
We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...
22 July 2024 4,285 9 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...
25 June 2024 4,286 4 View