Application of graphene in polar carriers and non-polar?

Maedeh Karami @Maedeh-Karami

10 November 2017 1 8K Report

How to make Graphene Preparation (with various percentages) ?

How does graphene work in polar and nonpolar carriers?

Maedeh Karami

@ Ali Farmani

Ok. Thats right. Thank U

Badges
Science topic

More Maedeh Karami's questions See All

How to cite SEER database?

Hi everyone I'm writing an article and I need data from SEER database. How should I add the reference?

13 December 2020 9,942 5 View

Why did the authors design a sociodemographic questionnaire?

This is a question from a journal reviewer who asked my manuscript. Can someone please guide me on how to prepare the reviewer's answer? Thanks. here is reviewer question. why did the authors...

16 November 2020 735 2 View

How can I fix the capacity curve of two different structure?

I have two frames for nonlinear analysis, one of them is CBFs and one of them is BRBFs ( the generals are the same, only lateral elements are different). When I drew the capacity curve of my...

11 November 2020 10,034 3 View

What is the best method to find a specific gender in Heteropteran insects?

I found an Hereoptera male and looking for its female in the field. Is there a specific method to lure and capture true bug females through keeping its male in the trap? What is the cue for luring...

23 August 2020 4,272 3 View

How could I find a proper solution and mesh for my physics in comsol?

I have 3 physics include mixer, radiation and chemical reaction related, which run in 2 different mesh and time dependent solution. The two study run in totally different techniques and when I...

29 July 2020 6,684 9 View

Why I couldn't get only step/frame zero (0) in abaqus?

I am simulating a quasi-static in abaqus explicit, but I couldn't see any step frame in visualization, although in monitoring window there are so many increment..

28 May 2020 5,184 3 View

Why am I not getting any results in Abaqus explicit?

the simulation in abaqus explicit completed but surprisingly when I click U or S or something, else everything is zero (below screenshot). any thoughts would be highly appreciated.

27 May 2020 4,548 10 View

Why the initial pressure in a fluid cavity simulation in Abaqus fall to zero just at the starting increments?

I am using fluid cavity capability for simulation of a water-filled container with Abaqus-Static-Standard. The container has an initial pressure and is been surrounded by another solid layer with...

21 March 2020 7,153 3 View

How can I save normal directions of solid elements in Abaqus?

Dear all, I need to have normal directions of solid elements in my 3D simulation with Abaqus. I know that in Visualization Module, Options tab> common or superimposed, there is the possibility...

28 February 2020 2,703 3 View

No title

I'm trying to collect milk from our knockout mice (at the end of the lactation stage) to isolate milk exosomes. But I have a hard time with milk collection from mice. I have used either pump or...

22 January 2020 4,527 1 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Which polarizers are usually used to measure the birefringence of zebrafish muscles?

I already found several publications on that topic, however, the specifications for the used filters are often missing. Some more specific information than "fish is placed between to polarizing...

23 February 2021 1,934 1 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How to calculate the Atomic Polar Tensor using DFT ?

Dear friends, I am a beginner at DFT calculation. I have done a structure optimization using DFT- B3LYP/6-31G*, Nevertheless, I don't know How to calculate the Atomic Polar Tensor (APT) in...

17 February 2021 9,082 3 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

How can I calculate teh crystallinity degree of graphene oxide?

I had treat my XRD diffraction pattern by Highscore to calculate the crystallinity degree Xc and I have the formula but I dont no the 2Theta of Ac and Aa to calculate Xc. Is it like polymers...

10 February 2021 6,305 5 View

About XRD details of pristine and doped RGO?

Hi Can anyone please help me know the XRD details of reduced graphene oxide, Nitrogen doped reduced graphene oxide, Sulphur doped reduced graphene oxide, Nitrogen and Sulphur co-doped reduced...

08 February 2021 3,033 3 View

What is the difference between Graphene Oxide and Expanded Graphite?

What are the main differences between Graphene Oxide and Expanded graphite, in terms of surface functionalities, conductivity, d-spacing and other features? Is the term expanded graphite...

06 February 2021 9,810 4 View

How to apply graphene oxide on an gold electrode?

Dear Fellows, now it is the time to push graphene applications further in terms of easy and low cost production surroundings. Thus I recently dived in the materia and I am facing tons of papers,...

02 February 2021 6,284 2 View