Is anyone working on CET analysis in continuous casting process?

anyone know how to calculate CET in cc?

03 April 2015 9,414 2 View

What is the scope of Phd other than being a Proffesor?

if someone is not interested in teaching then what is left for him after Phd?

03 April 2015 1,377 10 View

Can I calculate the reaction rate in EAF(continuous casting) and different products using ansys fluent?

can I calculate the reaction rate in AOD with 3 phases i.e. solid, liquid and slag with oxygen purging?

03 April 2015 9,313 0 View

How can I reduce the inclusion in continuous casting process using cfd ?

02 March 2015 9,976 5 View

Can we calculate the quenching time theoretically and also can we calculate it using cfd?

My material temp. is 900, if I want to know how much time it will take to reach 300 then how can we know that?

02 March 2015 4,894 3 View

Why isnt solidification and melting being shown in a 3-D modal in ansys cfd?

08 September 2014 9,518 5 View

How can I resolve the error in the interference zone?

08 September 2014 528 1 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View